background image

94

Festo — MSE6-C2M — 2022-08b

Malfunctions

Error
channel

Meaning

Remedy

Activation
parameter

m = module
number 0

Error number 10, upper limit value exceeded;
Depending on the parameterisation, the module reports the error when monitoring is activated.
Input signals will, however, still be processed.

Em.0

Upper flow rate
limit value
exceeded

Check the flow rate.

Check the parameterised limit value.

If necessary, adjust the monitoring limit value
parameter startup.

Pm.0.6:
Monitoring of
limit values

Em.2

Upper pressure
limit value
exceeded

Check the pressure.

Check the parameterised limit value.

If necessary, adjust the monitoring limit value
parameter startup.

Em.3

Upper pressure
change limit
value exceeded

Check the pressure change.

Check the parameterised limit value.

If necessary, adjust the monitoring limit value
parameter startup.

Check the system for leakage.

Error number 15, module/channel failed;
All electrical module functions are stopped.

Em.0

Flow sensor
defective

Power off/on necessary.

Replace the device if this error occurs repeat-
edly.

Cannot
be deactivated

Em.2

Pressure sensor
P2 defective

Power off/on necessary.

Replace the device if this error occurs repeat-
edly.

Summary of Contents for MSE6-C2M









































































































Reviews: