manualshive.com logo in svg

Festo CMMP-AS-***-M3 Series, Description

Share
Download
Festo CMMP-AS-***-M3 Series Description Download Page 23

6

Functions

Festo – GDCP-CMMP-M3-FW-EN – 1203NH

23

The following settings are possible:

Command

Function

Sync

Synchronisation is activated when positioning is started, if it was not already. If

the master is not stationary when positioning starts, the offset that occurs will

be made up in a controlled manner. The positioning speed used for this corres-

ponds to the speed of the master plus the positioning speed entered in the posi-

tioning record as an excessive increase in speed. The entries of the started posi-

tioning record are likewise used for the accelerations.

Sync Out

Synchronisation is deactivated when positioning is started, if it was not already.

Positioning starts with the current synchronous positioning speed (rotational

speed of the master). This results in controlled desynchronisation.

No Sync

Synchronisation is deactivated when positioning is started, if it was not already.

Positioning starts with the values for speed and acceleration entered in the posi-

tioning record.

Tab. 6.2

Commands for synchronisation

Remaining Distance

Enter the amount for the remaining distance message.

TFF (torque feed forward)

This value is used to permit the motor greater dynamic response during acceleration when large loads

are moved. The current required for approaching is increased by the set percentage (related to the

nominal current of the motor) after the positioning record is started. The result is a higher starting

torque that facilitates greater dynamic response. The value is determined experimentally.

Torque limitation

During standard positioning, the torque is limited only by the set nominal or peak currents. Torque limit-

ation provides another way of further limiting the torque during active positioning. The value should be

less than the set nominal current.

Start Delay

Waiting time until positioning starts.

Summary of Contents for CMMP-AS-***-M3 Series





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands