FarragTech CARD G Operating Manual Download Page 67

Page: 67 / 101

EXTENDED MODE

CARD G / FIT

V 6.15 E / April 2010

17.9

TATUS

EPORT

he S

TATUS

EPORT

accessed from the F

AULTS

CREEN

with the key

and facilitates trouble shooting and fault

diagnosis.

This screen shows the last 200 alarm and event messages. If there are more than 200 entries, the
oldest one will be replaced.

Additional process data are saved with the fault (or event):



Drying set value



Process air temperature



Temperature on the board of the FIT-controller



Dew point (if a dew point sensor is mounted)



Operating status of loading



Heater control signal



Compressed air consumption

The number in the upper display on the right hand side shows how many entries are present. The
number on the left hand side shows the running position of the displayed record.

The keys

and

must be used to scroll through the different records.

Pressing the key

for 3 seconds displays the last (oldest) record.

Pressing the key

for 3 seconds displays the first (youngest) record.

Summary of Contents for CARD G






































































































Search results

Summary of Contents for CARD G

Reviews:

Related manuals for CARD G

Brands by name

Popular brands

FarragTech CARD G, Operating Manual

Search results

Summary of Contents for CARD G

Reviews:

Related manuals for CARD G

Brands by name

Popular brands