FarragTech CARD G Operating Manual Download Page 39

Page: 39 / 101

START SCREEN AND LANGUAGE SELECTION

CARD G / FIT

V 6.15 E / April 2010

15.

START SCREEN AND LANGUAGE SELECTION

he S

TART

CREEN

appears on the FIT-controller every time the CARD G FIT unit is

powered on. If there is not made any selection by the operator, this screen remains displayed for
8 seconds before the M

AIN

CREEN

or the F

AULTS

CREEN

(in case of an alarm) is loaded

automatically.

Pressing the key

activates the E

ASY

ODE

which allows the operator to enter only set point

for the drying temperature and suction time for a vacuum loading device (if connected to the

CARD G FIT – see chapter 16 on page 39).

Pressing the key

activates the E

XTENDED

ODE

which allows the operator to edit all

parameters in the FIT-controller (see chapter 17 on page 40).

Summary of Contents for CARD G






































































































Search results

Summary of Contents for CARD G

Reviews:

Related manuals for CARD G

Brands by name

Popular brands

FarragTech CARD G, Operating Manual

Search results

Summary of Contents for CARD G

Reviews:

Related manuals for CARD G

Brands by name

Popular brands