FarragTech CARD G Operating Manual Download Page 57

Page: 57 / 101

EXTENDED MODE

CARD G / FIT

V 6.15 E / April 2010

17.6

ECIPES

17.6.1

STANDARD RECIPES

his screen includes a database

with preassigned drying data for the most common materials. They can be loaded into the drying
program. The user may decide to keep the preassigned data or alter the existing data. It is
recommended to use the C

USTOMER

ECIPES

(see chapter 17.6.2 on page 57) menu to program

custom recipes.

he S

TANDARD

ECIPES

are accessed from the screen with the D

RYING

ARAMETERS

with the

key .

The S

TANDARD

ECIPES

database contains 30 preassigned recipes. To scroll through the various

records, the cursor must be moved to the parameter R

ECIPE

-ID. Pressing the key

shows the next record.

The keys

and

can be used to decrease or increase the R

ECIPE

-ID by 5.

To load a record into the drying program, the keys

need to be pressed simultaneously.

The screen D

RYING

ARAMETERS

is opened and allows checking the loaded values once more. If

necessary, changes can be made again.

After pressing the key

the M

AIN

CREEN

appears.

Summary of Contents for CARD G






































































































Search results

Summary of Contents for CARD G

Reviews:

Related manuals for CARD G

Brands by name

Popular brands

FarragTech CARD G, Operating Manual

Search results

Summary of Contents for CARD G

Reviews:

Related manuals for CARD G

Brands by name

Popular brands