FarragTech CARD G Operating Manual Download Page 73

Page: 73 / 101

EXTENDED MODE

CARD G / FIT

V 6.15 E / April 2010

17.10.2

LAN SETTINGS

o establish an Ethernet

connection to the FIT-controller, the network addresses must be set to the local network
requirements. This can be done in the screen LAN-P

ARAMETERS

which is activated from the

screen D

ATA

RANSFER

through the key

The E

DITOR

CREEN

must be used to set the addresses as desired. To confirm the altered data, the

keys

need to be pressed.

A message will be shown in the display when the values are accepted.

Finally, the CARD G FIT must be powered off and on again to accept the new LAN parameters.
The drying process must be deactivated and the cool down period must be expired before the
unit may be powered off.

The key

is to be applied to return from this screen back to the screen D

ATA

RANSFER

Summary of Contents for CARD G






































































































Search results

Summary of Contents for CARD G

Reviews:

Related manuals for CARD G

Brands by name

Popular brands

FarragTech CARD G, Operating Manual

Search results

Summary of Contents for CARD G

Reviews:

Related manuals for CARD G

Brands by name

Popular brands