FarragTech CARD G Operating Manual Download Page 75 | Manualshive

Page: 75 / 101

background image

EXTENDED MODE

CARD G / FIT

73

V 6.15 E / April 2010

Unit Temperature

F

ACTORY

S

ETTING

:

[C]

The values [C] and [F] might be selected in this parameter.
Depending on this adjustment, the temperature values are indicated as °C (centigrade) or as °F (degree
Fahrenheit) in different screens.

Process Data Cycle

F

ACTORY

S

ETTING

:

30s

The values for the characteristics of the drying temperatures in the M

AIN

S

CREEN

and for the data table

in the P

ROCESS

D

ATA

S

CREEN

(see chapter 17.3 on page 48) are recorded at the time interval set in this

parameter.
If more than 250 data sets recorded, each new data set will replace the oldest one.
Retaining the factory setting of 30 seconds traces the drying temperatures in the M

AIN

S

CREEN

and the

data in the P

ROCESS

D

ATA

S

CREEN

over the past 125 minutes.

Dew Point Sensor max.

F

ACTORY

S

ETTING

:

+20°C

The highest value of the measurement range of the optional dew point meter is set in this parameter.
The appropriate value can be found on the name plate of the dew point meter.

Dew Point Sensor min.

F

ACTORY

S

ETTING

:

-60°C

The lowest value of the measurement range of the optional dew point meter is set in this parameter. The
appropriate value can be found on the name plate of the dew point meter.

Voltage

F

ACTORY

S

ETTING

:

230V

Based on the standard supply voltage of 230 Volts, the electrical power consumption in the E

NERGY

S

CREEN

is calculated.

This value may be altered if the supply voltage to the CARD G FIT unit differs from 230 Volts.

Offset [kWh]

F

ACTORY

S

ETTING

:

+ 0.0 %

An offset might be set to correct deviations between a measured and the calculated value for the power
consumption displayed in the E

NERGY

S

CREEN

.

The deviation must be entered as a value in percentage.

«
...
73
74
75
76
77
...
»

Summary of Contents for CARD G






































































































Reviews:

No comments

Related manuals for CARD G

Brand: B&K Pages: 12

Brand: Ace Pages: 17

Brand: ACE INSTRUMENTS Pages: 33

Brand: ACE INSTRUMENTS Pages: 2

Brand: ACE INSTRUMENTS Pages: 2

Brand: TapFlo Pages: 35

Brand: DANA Pages: 8

Brand: 2E Pages: 6

Brand: XanLite Pages: 4

Brand: Velp Scientifica Pages: 12

Brand: Yamaha Pages: 24

Brand: J&M Pages: 33

Brand: RAPID REBOOT Pages: 18

Brand: MacDon Pages: 170

Brand: MacDon Pages: 108

Brand: MacDon Pages: 108

Brand: MacDon Pages: 51

Brand: MacDon Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands