FarragTech CARD G Operating Manual Download Page 68

Page: 68 / 101

EXTENDED MODE

CARD G / FIT

V 6.15 E / April 2010

17.10

YSTEM

ARAMETERS

he S

YSTEM

ARAMETERS

include data which need to be changed only in case of special

applications (for detailed information see SYSTEMS MANUAL CARD G FIT). The parameters can

be accessed after a password has been entered.
The P

ASSWORD

CREEN

is attained from the screen with the D

RYING

ARAMETERS

with the key

To enter the password, the key

must be pressed. A blinking field prompts the operator to

input the password using the numeric keypad. Pressing the key

confirms the value.

The message below appears in case of wrong password.

Pressing the key

allows the password to be entered once more. The procedure to input the

password can also be abandoned with the key

. To return to the M

AIN

CREEN

the key

needs to be pressed.

Summary of Contents for CARD G






































































































Search results

Summary of Contents for CARD G

Reviews:

Related manuals for CARD G

Brands by name

Popular brands

FarragTech CARD G, Operating Manual

Search results

Summary of Contents for CARD G

Reviews:

Related manuals for CARD G

Brands by name

Popular brands