FarragTech CARD G Operating Manual Download Page 74 | Manualshive

Page: 74 / 101

background image

EXTENDED MODE

CARD G / FIT

72

V 6.15 E / April 2010

17.10.3

UNIT SELECTION

T

he parameters for U

NIT

S

ELECTION

are accessed from the screen C

ONVEYING

M

ODE

with the key

. Among other parameters, the displaying units for air flow and temperature can be adjusted

in this screen.

CARD G Type

F

ACTORY

S

ETTING

:

Automatic detection

The values 1G, 3G and 6G might be selected in this parameter
This parameter can only be changed if parameter T

YPE MANUAL

is set to ON.

As a standard, the FIT-controller detects the correct CARD G FIT type automatically. A manual
adjustment will only be required if the automatic detection fails or a special drying process is required.

Type manual

F

ACTORY

S

ETTING

:

OFF

The values OFF and ON might be selected in this parameter.
This parameter must be set to ON to allow the adjustment of the parameter CARD

G

T

YPE

. With setting

OFF in this parameter, the FIT-controller detects the correct CARD G FIT type automatically.
A manual adjustment will only be required if automatic detection fails or a special drying process is
required.

Unit Air Flow

F

ACTORY

S

ETTING

:

[Nm3/h]

The values [Nm3/h] and [cfm] might be selected in this parameter.
Depending on this adjustment, the air flow values are indicated as cfm (cubic feet per minute) or as
Nm³/h (standard cubic meters per hour) in different screens.

«
...
72
73
74
75
76
...
»

Summary of Contents for CARD G






































































































Reviews:

No comments

Related manuals for CARD G

Brand: CAMAG Pages: 40

DISHSTAR ADA-SEER

Brand: Jackson Pages: 2

Brand: Quivogne Pages: 13

Brand: Mackie Pages: 34

Brand: Mackworth Pages: 38

Brand: P&P Pages: 6

Brand: RAMVAC Pages: 53

Brand: Airway Pages: 2

Brand: Crazy Foil Pages: 8

Life/form LF03608

Brand: Nasco Healthcare Pages: 6

Brand: Beta Pages: 8

Brand: Landoll Pages: 40

INSPIRE Mulit-gym M2

Brand: Hammer Pages: 26

Brand: Ibiza Pages: 40

Brand: ABI Attachments Pages: 17

SkyWriter HPX M-5

Brand: X-laser Pages: 65

SC-88 Sound Canvas

Brand: Roland Pages: 146

Lakeland Ambleside

Brand: Quest Leisure Products Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands