Fanotec MECHA C2 User Manual Download Page 8

Page: 8 / 122

MECHA C2 User’s Guide

v.02.5

Simple Mode

Before practicing what you read in this section, please make sure that C2

works in

Simple Mode

Power on MECHA

by pressing the

button for 3 to 5 seconds (long

press). It may take about 35-45 seconds to start, then MECHA reaches

the

idle status

and the display will show

1. either the

Preset (P) Menu

2. or the rotators in use and the dynamic IP address.

Case 1

. The display shows the

Preset (P) Menu

●

Press the

button to switch to

Config (C) Menu

●

If the first option in this menu is

SIMPLE MODE

, just leave it

unchanged. Otherwise, press the

button to change it to

SIMPLE MODE

Case 2

. The display shows the rotators in use and the IP address:

●

Long press the

button to enter

Menu Mode

●

Press the

button to switch to

Config (C) Menu

●

Press the

button to change the first option to

SIMPLE MODE

📹

https://youtu.be/gBGxE5Q11xI

Introducing Simple / Advanced Mode – MECHA C2

Summary of Contents for MECHA C2



























































































































Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands

Fanotec MECHA C2, User Manual

Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands