Fanotec MECHA C2 User Manual Download Page 28

Page: 28 / 122

MECHA C2 User’s Guide

v.02.5

Panorama with Automatic Shooting Pattern

Using C2’s Menu

This method requires the firmware version

(1)2272

or newer, and works for

any lens from 4 to 1000mm, including fisheye lenses.
MECHA will compute a preset for your lens based on the data it receives

when performing the following procedure:

●

Power on MECHA as usual and

make sure the upper rail is in the

level

position.

●

Place a small object in front of

MECHA so that it is right in the

center of the frame. The distance

to the target object is not

important.

●

The camera and lens must be set

the same as for shooting the

actual panorama.

●

Now, in the

Preset (P) Menu

, use the

button to find an empty option

or editable preset.

●

Press the

button to enter edit

mode.

●

The first parameter is already selected and flashes, which means you
can adjust it. Use the

button to find the

AUTO

value. You can adjust

the other parameters, if necessary. We assume that you have read the

chapter on editing the preset and therefore know how to work with

parameters.

●

Press the

button to confirm.

●

Press the

button again to launch the preset.

●

When the preset asks you to

Set POSITION

, you just have to press the

button to confirm, assuming that the upper rail is in the

level

position and the target object is already in the center of the frame.

●

The following message appears on the display to remind you what to

do next, and you have 10 seconds to read it:

Summary of Contents for MECHA C2



























































































































Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands

Fanotec MECHA C2, User Manual

Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands