Fanotec MECHA C2 User Manual Download Page 36

Page: 36 / 122

●

PANORAMA TEST RAISED

— A

test

preset for a multi-row panorama: 12

shots around, 3 rows ‒ at 0° and +/-45° ‒ plus zenith and nadir. Make
sure the upper rail is in the

raised

position, then press the

button

to launch the preset.

●

KIT LENS 18(29) LEVEL

— A preset for a multi-row panorama: 12 shots

around, 3 rows ‒ at 0° and +/-45° ‒ plus zenith and nadir.

●

FE 12mm NZ Level

— A preset for 12mm fisheye lenses, 4 shots around,

plus nadir and zenith.

●

FE 16mm NZ Level

— A preset for 16mm fisheye lenses, 6 shots around,

plus nadir and zenith.

●

FE 24mm NZ Level

— A preset for 24mm fisheye lenses, 8 shots around, 2

rows ‒ at -30° and +30° ‒ plus zenith and nadir.

After pressing the

button to launch the preset, the four presets above

will require confirmation of position and direction of rotation:

○

Set POSITION

: position the upper rail in the

level

position as shown

Simple Rotations

. Press the

button to confirm.

○

ROT. SENSE

: press either the

button to start shooting.

Config (C) Menu

●

SIMPLE / ADVANCED MODE is ON

— Press the

button to switch

between the two options. The main difference between the two modes

is that in

SIMPLE MODE

you are always in one of C2's menus and some

operations are therefore easier to perform.

●

MECHA ID

— Press the

button to show the MECHA’s ID, which is an

identifier comprised of letters and numbers and is part of the

MAC

ADDRESS

●

MAC ADDRESS

— Press the

button to show the entire MAC address

(media access control address), which uniquely identifies your MECHA.

MECHA C2 User’s Guide

v.02.5

Summary of Contents for MECHA C2



























































































































Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands

Fanotec MECHA C2, User Manual

Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands