manualshive.com logo in svg

Fanotec MECHA C2, User Manual

Share
Download
Fanotec MECHA C2 User Manual Download Page 104

104

MECHA C2 User’s Guide

v.02.5

© 2021 FANOTEC

2<

or

2>

Executes the

Preset 2

to the left or to the right.

By default, the

Preset 2

consists of 6 shots around, or it is the preset

saved with the

[Save2]

UI button.

3<

or

3>

Executes the

Preset 3

to the left or to the right.

By default, the

Preset 3

consists of 8 shots around, or it is the preset

saved with the

[Save3]

UI button.

131<

or

131>

Executes a panorama of 6 shots around to the left or to the right.

132<

or

132>

Executes a panorama of 12 shots around to the left or to the right.

1312<

or

1312>

Executes a panorama of 12 shots around, 3 rows ‒ at 0° and at +/-45° ‒

plus zenith and nadir, to the left or to the right. The lower rotator must

be

parked

, i.e. oriented upward, as for the zenith photo.

1313<

or

1313>

The same as 1312, but with the upper rotator in the

level

position. First

time, please test the codes without camera mounted on the panohead.

1321<

or

1321>

The same as 1312, but with the upper rotator in the

raised

position. First

time, please test the codes without camera mounted on the panohead.

121< → MECHA ID

Shows the MECHA’s ID, like “

123ABC

“.

123< → MAC ADDRESS

Shows the

entire

MAC address, like “

123ABC123ABC

“.

323< → IP ADDRESS

Shows the

full

IP address, like “

192.168.0.100

“.

Summary of Contents for MECHA C2



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands