Fanotec MECHA C2 User Manual Download Page 20

Page: 20 / 122

MECHA C2 User’s Guide

v.02.5

●

Press the

button for about 3 to 5 seconds to power on MECHA, and

wait until MECHA reaches the idle status (and the

Preset (P) Menu

shown on C2’s display).

●

If MECHA doesn’t reach this status, then please power it off, by pressing
the

button 3 seconds, and contact us at

[email protected]

●

Press the

button to switch to

Config (C) Menu

●

Press the

button to select page 8.

●

Press the

button several times, until

UPDATE USING H-SPOT

appears on the display, as shown in the image below.

●

Press the

button to launch the update. Now MECHA starts scanning

the existing networks, and when it connects to the previously created

hot-spot, two beeps are heard. The UPDATE USING H-SPOT option will

update the firmware using the MECHA-UPDATE hot-spot you set.

●

Now, deactivate the hot-spot, power MECHA off, then power it on.

If you use the above option without

creating the hot-spot, the firmware

will be updated later, when the

internet will be available.

The update may take up to 5 minutes, but

it could take longer in case of slow

Internet connection.

For more details on using C2’s menus,

please read

C2’s Menu Mode

The response shown on the display will be:

”

No update found!

”

, if

Internet is not available for MECHA.

Please do not turn off MECHA while updating the firmware!

Summary of Contents for MECHA C2



























































































































Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands

Fanotec MECHA C2, User Manual

Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands