Fanotec MECHA C2 User Manual Download Page 109

Page: 109 / 122

109

MECHA C2 User’s Guide

v.02.5

32123<

Updates the firmware, if possible. To update the firmware using the

32123<

code, MECHA must be in

STA

AP+STA

mode and connected to a

Wi-Fi with Internet access, before entering the code. Depending on

Default Mode

, it may be necessary to enable temporarily

STA

AP+STA

start via buttons, then enter the

32123<

code. MECHA will show on the

display

"No update found"

if no update was found, or “

!!!

” if there is no

Internet connection.

312123< → UPDATE USING H-SPOT

Update the firmware using a hot-spot with the name

MECHA-UPDATE

and (default) password

87654321

, which needs to be created and active

before entering the code.

312< → UPDATE

Re-updates the current firmware.

3231<

Code for testing the IR Remote. After the code is entered, MECHA will not

execute the commands received from the IR Commander’s buttons.

Instead, it will only beep and show on its display the code of the button

pressed (after the button is released), and over the battery symbol in UI.
To end the test, press the power button,

2313< → CHANGE SENSE LEFT-RIGHT

Changes the sense of left/right rotation when it is done manually using
the

buttons.

2323< → CHANGE SENSE UP-DOWN

Changes the sense of up/down rotation when it is done manually using

the

buttons.

The following codes should match with the current rotators connected to

the controller.

13131< → SET E1 AS ROTATOR 1

Sets E1 as lower rotator.

Summary of Contents for MECHA C2



























































































































Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands

Fanotec MECHA C2, User Manual

Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands