Fanotec MECHA C2 User Manual Download Page 39

Page: 39 / 122

MECHA C2 User’s Guide

v.02.5

●

CHANGE SENSE LEFT-RIGHT

— Press the

button to change the sense

of left/right rotation when it is done manually using the

and

buttons.

●

CHANGE SENSE UP-DOWN

— Press the

button to change the sense of

up/down rotation when it is done manually using the

and

buttons.

●

ARROWS speed ... RPM

— Press either

button to enter edit

mode and adjust the rotational speed when a button is held down (see

Arrow Buttons

●

INTERVAL 1/2/3

and

Interval 1/2/3 speed

are the angles of rotation and

corresponding speeds for

Simple Rotations

. Press either

button to enter edit mode and adjust their value.

●

LEVEL AMOUNT

— The angle at which the upper rail is rotated after

powering on if you press the

button when the display shows

-+=

The upper rail should be in the

parked

position at powering ON.

Enter edit mode using the

button and adjust the

LEVEL AMOUNT

, or

adjust it right after the rotation, when there is the possibility to omit the
confirmation of the change, meaning that you can press the

button

instead of pressing the

button as usual. This means that the new

value is only available during the current work session, until MECHA is

powered off.
If the upper rotator has a position sensor, MECHA will use it as

reference and the rotation will be more accurate. When adjusting the

LEVEl AMOUNT

○ X

– will be shown if you are in the area of the positioning sensor

○ !

– will be shown if the sensor is not detected at leveling, which is

normal for E1, and may be necessary to disassemble and assemble

the upper rail rotated 180° in the case of E2 or P1 .

●

SHOW HINTS is ON / OFF

— Press the

button to switch between the

two options. If enabled, the display will show contextual information to

help you use C2’s Menus.

Summary of Contents for MECHA C2



























































































































Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands

Fanotec MECHA C2, User Manual

Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands