Fanotec MECHA C2 User Manual Download Page 77

Page: 77 / 122

MECHA C2 User’s Guide

v.02.5

Working with Presets

Programming a Preset Using Parameters

A programming method available starting with firmware version

(1)2134

Being connected with your smartphone, or computer, to the MECHA’s SSID

(MECHA’s Wi-Fi), enter

one

of the following urls in the browser address bar

and tap

Access

, or press the

Enter

key (this will overwrite the preset already

assigned to the

button):

192.168.8.1/preset?b=1&s=12&p=2

192.168.8.1/preset?b=1&f=30&p=2

The page will ask for credentials, which are:

admin

Mecha

(by default).

Now check that the position for the upper rail is

level

, or as specified on the

Configuration

page.

If you press the

buttons:

●

MECHA will take 12 shots around (

s=12

) if you enter

192.168.8.1/preset?

b=1

s=12

f=30

p=2

●

or it will start to shoot a full 360° panorama for a 30 mm lens (FF equiv.)

(

f=30

) if you enter

192.168.8.1/preset?

b=1

f=30

p=2

Creating a preset using parameters always overwrites one of the

following presets:

Button 1

Button 2

, or

Button 3

, depending on

the value passed through the

parameter.

This method of programming, or creating, a preset consists in

connecting to the User Interface (see

How to Access the UI

) and

passing some parameters in the url. This preset is assigned to one of

MECHA’s buttons, so it can be executed by pressing that button, and
the

buttons.

Summary of Contents for MECHA C2



























































































































Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands

Fanotec MECHA C2, User Manual

Search results

Summary of Contents for MECHA C2

Reviews:

Brands by name

Popular brands