Fagor CNC 8055 Operating Manual Download Page 62

Page: 62 / 256

·62·

Operating manual

CNC 8055

CNC 8055i

EXECUTE /

SIMULATE

·T· M

ODEL

OFT

: V02.2

Block se

arch.

Swi

tch

ing from

simul

tion to executio

4.1.4

Home searching restrictions

Block search is restricted in the following scenarios:

• In a program where a particular scaling factor is activated, the block search is automatically or

manually restricted to a block after that activation.

• In a program where axes are slaved with G77 or using PLC SYNCRO marks, the block search

is automatically or manually restricted to a later block.

The same restriction applies to a program having spindle synchronization.

• In a program that applies mirror image via PLC using MIRROR marks, the automatic or manual

search are restricted to later blocks.

• In a program containing a home search (G74), the automatic or the manual search is restricted

to later blocks.

4.1.5

Disabling the simulation and block search modes

The simulation and block search modes are available depending on the setting of g.m.p. DISSIMUL
(P184).

Summary of Contents for CNC 8055

































































































































































































































































Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands

Fagor CNC 8055, Operating Manual

Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands