Fagor CNC 8055 Operating Manual Download Page 73

Page: 73 / 256

Operating manual

CNC 8055

CNC 8055i

EXECUTE /

SIMULATE

·T· M

ODEL

OFT

: V02.2

·73·

"MODIFY OFFSETS" softkey

This option shows (at the top) a help graphic and the tool fields that can be edited. The data may
be selected with the [



] [



] [



] [



] keys or from the softkey menu.

It is also possible to select a new tool to correct it. To select a new tool, enter its number in the T
field and press [ENTER].

• The I and K data can be changed for the active tool. To apply the new values, the tool must be

selected once again.

• The I, K and D values may be modified if it is not the active tool.

The values entered in the I - K fields are incremental; they are added to the ones already in the table.
The "I" data is given in diameter.

The maximum value that may be entered in each I - K field is limited by machine parameters
MAXOFFI and MAXOFFK. When trying to enter a greater value, the relevant message will be
displayed.

Summary of Contents for CNC 8055

































































































































































































































































Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands

Fagor CNC 8055, Operating Manual

Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands