Fagor CNC 8055 Operating Manual Download Page 11

Page: 11 / 256

CNC 8055

CNC 8055i

·7·

VERSION HISTORY

Here is a list of the features added in each software version and the manuals that describe them.

The version history uses the following abbreviations:

INST

Installation manual

PRG

Programming manual

OPT

Operating manual

OPT-MC

Operating manual for the MC option.

OPT-TC

Operating manual for the TC option.

OPT-CO

Manual of the CO manual

Software V01.00

October 2010

First version.

Software V01.20

April 2011

Software V01.08

August 2011

Software V01.30

September 2011

List of features

Manual

Open communication.

INST

Improvements to Look Ahead machining.

INST

Blocks with helical interpolation in G51.

PRG

G84. Tapping with relief.

PRG

List of features

Manual

Spindle parameter OPLDECTI (P86).

INST

List of features

Manual

Gear ratio management on Sercos spindles

INST

Improved feedrate limit management (FLIMIT).

INST

New type of penetration in lathe type threading cycles.

PRG

Improved lathe type thread repair. Partial repair.

PRG

MC option: Rigid tapping with relief.

OPT-MC

TC option: New type of penetration in threading cycles.

OPT-TC

TC option: Improved thread repair. Partial and multi-entry (start) thread repair.

OPT-TC

TC option: Zig-zag entry to the groove at the starting point of the groove.

OPT-TC

Summary of Contents for CNC 8055

































































































































































































































































Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands

Fagor CNC 8055, Operating Manual

Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands