Fagor CNC 8055 Operating Manual Download Page 113

Page: 113 / 256

Operating manual

CNC 8055

CNC 8055i

MANUAL

·T· M

ODEL

OFT

: V02.2

·113·

"MM/INCHES" softkey

This softkey toggles the display units for the linear axes from millimeters to inches and vice versa.

The lower right-hand window will indicate which units are selected (MM/INCH).

Note that this switching obviously does not affect the rotary axes which are shown in degrees.

Actual and following error

It shows the real position of the axes and their following
error.

When the C axis is active, the position of the X-C axes
correspond to the transformed coordinates.

PLC

Access the PLC monitoring mode.

Position

It shows the real position of the axes referred to part
zero and to machine zero (home)

When the C axis is active, the position of the X-C axes
referred to part zero correspond to the transformed
coordinates.

Summary of Contents for CNC 8055

































































































































































































































































Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands

Fagor CNC 8055, Operating Manual

Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands