Fagor CNC 8055 Operating Manual Download Page 12

Page: 12 / 256

·8·

CNC 8055

CNC 8055i

Versio

n history

Software V01.31

October 2011

Software V01.40

January 2012

Software V01.60

December 2013

Software V01.65

January 2015

Software V02.00

February 2014

List of features

Manual

CNC 8055 FL Engraving model

INST / OPT/ PRG

List of features

Manual

Execution of M3, M4 and M5 using PLC marks

INST / PRG

Values 12 and 43 of variable OPMODE in conversational work mode.

INST / PRG

List of features

Manual

Auto-adjustment of axis machine parameter DERGAIN.

INST

New value for axis machine parameter ACFGAIN (P46).

INST

Value 120 of the OPMODE variable.

INST / PRG

List of features

Manual

Block processing time of 1 ms on the "CNC 8055i FL Engraving" model.

INST / OPT/ PRG

List of features

Manual

Profile machining in segments. J parameter for G66 and G68 cycles.

PRG

Calls to subroutines using G functions.

INST / PRG

Anticipated tool management.

INST

Managing "PNG" and "JPG" graphic elements.

INST

New values for parameters MAXGEAR1..4 (P2..5), SLIMIT (P66) and MAXSPEED (P0).

INST

Retracing function of 2000 blocks.

INST

Quick block search.

OPT

Local subroutines within a program.

PRG

Avoid spindle stop with M30 or RESET. Spindle parameter SPDLSTOP (P87).

INST

Programming T and M06 with associated with a subroutine in the same line.

PRG

New values of the OPMODE variable.

INST / PRG

New variables: DISABMOD, GGSN, GGSO, GGSP, GGSQ, CYCCHORDERR.

INST / PRG

Possibility to set the parameters of SERCOS nodes in a non-sequential order.

INST

WRITE instruction: “$” character followed by “P”.

PRG

Cancel additive handwheel offset with G04 K0. General parameter ADIMPG (P176).

INST / PRG

Ethernet parameter NFSPROTO (P32). TCP or UDP protocol selection.

INST

Face thread repair cycle.

OPT TC

Penetration increment (step) in thread repair.

INST / OPT TC

API compliant thread.

OPT TC

Roughing by segments in inside profiling cycles 1 and 2.

INST / OPT TC

Programming the Z increment and the angle on threads.

INST / OPT TC

Reversal of the starting and final point of the face thread repair.

INST / OPT TC

Manual tool calibration without stopping the spindle during each step.

INST / OPT TC

Summary of Contents for CNC 8055

































































































































































































































































Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands

Fagor CNC 8055, Operating Manual

Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands