Fagor CNC 8055 Operating Manual Download Page 230

Page: 230 / 256

·230·

Operating manual

CNC 8055

CNC 8055i

13.

DIAGNOSIS

·T· M

ODEL

OFT

: V02.2

Adjustments

CNC variables that may be assigned to a channel

Indicate the desired variable.

Example:

ANAI1

FREAL

FLWEX.

Fagor Sercos or CAN drive variables that may be assigned to a channel

Indicate the desired axis or spindle and variable, separated by a period. The auxiliary spindle is
identified with the prefix "AS".

Example:

X.CV3

Y.SV1

S1.SV2

AS.SV1

Variable

Description

ANAI(1-8)

Voltage of input 1-8.

ANAO(1-8)

Voltage to apply to output 1-8.

FREAL

Actual (real) CNC feedrate.

FREAL(X-C)

Actual (real) X-C axis feedrate

FTEO(X-C)

Theoretical X-C axis feedrate

FLWE(X-C)

X-C axis following error.

ASIN(X-C)

"A" signal of the CNC's sinusoidal feedback for the X-C axis.

BSIN(X-C)

"B" signal of the CNC's sinusoidal feedback for the X-C axis.

DRPO(X-C)

Position indicated by the Sercos drive of the X-C axis.

SREAL

Real spindle speed.

FTEOS

Theoretical spindle speed.

FLWES

Spindle following error.

ASINS

"A" signal of the CNC's sinusoidal feedback for the spindle.

BSINS

"B" signal of the CNC's sinusoidal feedback for the spindle.

DRPOS

Position indicated by the Sercos drive of the spindle.

SSREAL

Real speed of the second spindle.

SFTEOS

Theoretical speed of the second spindle.

SFLWES

Following error (lag) of the second spindle.

SASINS

"A" signal of the CNC sinusoidal feedback for the second spindle.

SBSINS

"B" signal of the CNC sinusoidal feedback for the second spindle.

SDRPOS

Position indicated by the Sercos drive of the second spindle.

Variable

Description

CV3

CurrentFeedback

SV1

VelocityCommand

SV2

VelocityFeedback

SV7

VelocityCommandFinal

TV1

TorqueCommand

TV4

VelocityIntegralAction

RV1

FeedbackSine

RV2

FeedbackCosine

RV51

Feedback2Sine

RV52

Feedback2Cosine

Summary of Contents for CNC 8055

































































































































































































































































Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands

Fagor CNC 8055, Operating Manual

Search results

Summary of Contents for CNC 8055

Reviews:

Related manuals for CNC 8055

Brands by name

Popular brands