Factory Five Racing '33 Hot Rod Assembly Manual Download Page 323 | Manualshive

Page: 323 / 710

background image

322

www.factoryfive.com

508-291-3443

Transmission Tunnel Cover



Jig saw or air saw, ¼” drill bit, drill, marker, masking tape, ¼” hex drive bit, silicone, sanding tool,

measuring tape, clamps.



Mounted aluminum/components, body finish components, shifter boot components



The pictures shown are of the older tunnel but the process is similar.



The transmission tunnel is designed to be adjustable to allow maximum foot room for every

engine/transmission combination.

Insert the fiberglass transmission tunnel into the cockpit.
Look at the bellhousing to tunnel clearance. It is advisable to have at least ½” clearance between the
bellhousing and the tunnel to allow the engine to torque under acceleration without hitting.
Measure both sides of the engine to ensure clearance.
If there is enough bellhousing clearance, remove the transmission tunnel.

Cut the middle area fiberglass holding the two sides of the transmission tunnel together at the front the
same amount measured before.

Place the tunnel in the cockpit check clearance to the bellhousing.
Check the hole for the emergency brake handle. If necessary, mark and cut the hole opening in the flange.
Drill and rivet the tunnel to the floor.

«
...
321
322
323
324
325
...
»

Summary of Contents for '33 Hot Rod







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for '33 Hot Rod

Brand: AC Schnitzer Pages: 16

Brand: Ultra Start Pages: 8

Brand: Vaisala Pages: 24

Brand: Thule Pages: 8

Road Ready Seat Protector

Brand: Wagan Pages: 12

Brand: Chevrolet Pages: 50

Brand: iArmor Pages: 4

Brand: ideus Pages: 159

PRIME DESIGN URX-001-E

Brand: Safe Fleet Pages: 8

Brand: Mercedes-Benz Pages: 39

Brand: Mitsubishi MOTORS Pages: 416

Brand: Maserati Pages: 302

Brand: r.LiNK Pages: 21

Brand: Oldsmobile Pages: 380

Brand: Cadillac Pages: 19

Brand: Calix Pages: 4

2000 Accord Sedan

Brand: Honda Pages: 320

Brand: DRAGONFIRE Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands