manualshive.com logo in svg

Factory Five Racing '33 Hot Rod, Assembly Manual, Page: 203 / 710

Share
Download
Factory Five Racing '33 Hot Rod Assembly Manual Download Page 203

202 

www.factoryfive.com 

508-291-3443 

 

 

Cut the yellow and white rear turn signal light wires off the turn signal connectors that are for the dash 
turn signal switch so that the turn signal lights do not back feed and light the front turn signals when the 
brakes are pressed. 

Fan Wiring 

 

Follow the directions in the chassis harness instructions 

 

Carbureted Engine 

 

Run the coil wires with the alternator wires and gauge sender wires for use with the coil. 

 

Fuel  Injected Engine 

 

Leave the coil and crank wires in the footbox and connect them to the power wires for the EFI harness 
according to the EFI harness instructions. 
If the EFI harness uses its own wires for the fuel pump, remove the fuse for the fuel pump from the fuse 
panel and cut and solder the fuel pump wire from the EFI harness onto the chassis harness wire. 

 

    If using a Coyote engine, refer to the available “Coyote Install” instructions. 

 

Alternator 

 

Run the alternator wires along the top of the engine to the alternator. 

Summary of Contents for '33 Hot Rod







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments