![background image](http://html1.mh-extra.com/html/factory-five-racing/33-hot-rod/33-hot-rod_assembly-manual_3152077604.webp)
603
508-291-3443
Final Prep
Sand paper
If using fenders, now is a good time to fit and prep them. Make sure the car is aligned before
cutting if doing bike fenders.
All of the exterior body accessories, headlights, windshield and exhaust must be mounted to the car to
obtain the correct body location in order to create the correct gaps and opening sizes on the car before it is
painted.
One of the most important details in the bodywork is the finish on all the edges and openings. All of the
following edges are visible on the finished car and need to be evened out and have a small radius sanded
in for a good looking finish.
Doors
Hood
Trunk
Exhaust
Roll Bar cut outs
Door openings
Cockpit edges
The side body edges are not as visible but just taking a little time here to get the lines straight and a small
radius makes a much nicer finish.
Mark the trunk and door hinges before removing the last time so that you can bolt them back together in
the same position that they came off. They may still need minor adjusting during final body installation
but this will get you much closer.
Summary of Contents for '33 Hot Rod
