manualshive.com logo in svg

Factory Five Racing '33 Hot Rod, Assembly Manual, Page: 550 / 710

Share
Download
Factory Five Racing '33 Hot Rod Assembly Manual Download Page 550

549 

www.factoryfive.com 

508-291-3443 

 

 

Carefully push the felted rubber seal onto the top of the door. If necessary use tin snips to trim the ends 
so that they can push all the way on. If you can not push it all the way on, check the thickness of the top 
of the fiberglass door. It can be no thicker than 

3

/

16

” for the felted rubber seal to go on. Grind the inside 

of the door if necessary to remove material. 

 

Carefully remove the felted rubber seal parts. 

Summary of Contents for '33 Hot Rod







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments