Factory Five Racing '33 Hot Rod Assembly Manual Download Page 489

Page: 489 / 710

488

www.factoryfive.com

508-291-3443

Mark the hole for the hood release pull under the dash on inner edge of door jam by drawing around the
flange.



Make sure to leave clearance for the door when the door is shut.

Use this template to mark the inside area to cut and to drill the

” mounting screw holes. Use a ruler to

check the scale before using.

Pull the cable so that it just comes through the hole.

Summary of Contents for '33 Hot Rod







































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for '33 Hot Rod

Reviews:

Factory Five Racing '33 Hot Rod, Assembly Manual, Page: 489 / 710

Search results

Summary of Contents for '33 Hot Rod

Reviews: