
219
508-291-3443
Optional Clutch Cable
Clutch cable, insulated clip hardware
For use with optional manual transmission components.
Slide the clutch cable end through the clutch cable spacer and loop the cable over the quadrant.
Route the clutch cable down to the bellhousing. Using zip ties or insulated clips tie the cable safely away
from the headers and the moving steering components. It can be fastened to the engine using the bracket
on the cable to the front lower bolt that holds the starter cable just before it leaves the block or, to the
lower engine bay ¾” tubing.
Make sure that the cable is clear of the hot exhaust header and the steering shaft or the cable may fail
prematurely.
Connect the clutch cable to the bellhousing and the clutch fork.
Thread the cable end adjuster nut on so that the cable has no play in it.
Adjust the pedal closer or further away as desired by screwing the pedal stop screw up or down.
Check the full range of travel for the clutch pedal.
There may be a small amount of movement in the firewall if you try pressing the clutch. Keep in
mind that the firewall will get attached to the body which will help support/reinforce the firewall.
Summary of Contents for '33 Hot Rod
