Factory Five Racing '33 Hot Rod Assembly Manual Download Page 420

Page: 420 / 710

419

www.factoryfive.com

508-291-3443



If it is not possible to center the striker in the hole, remove the striker mount and grind the built-

in washer.

Tighten the striker mount using a ½” socket.
Tighten the striker on the mount using a ¾” socket and ⅝” wrench.

Door Latches



Ruler, marker, ⅜” socket, ratchet, drill, ¼”, ⅜” drill bits, tin snips, chassis grease



33 door handle components

Summary of Contents for '33 Hot Rod







































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for '33 Hot Rod

Reviews:

Related manuals for '33 Hot Rod

Brands by name

Popular brands

Factory Five Racing '33 Hot Rod, Assembly Manual

Search results

Summary of Contents for '33 Hot Rod

Reviews:

Related manuals for '33 Hot Rod

Brands by name

Popular brands