manualshive.com logo in svg

Exabyte VXA-2 AUTOPAK1X7, Product Manual, Page: 92 / 104

Share
Download
Exabyte VXA-2 AUTOPAK1X7 Product Manual Download Page 92

84

P

RODUCT

 M

ANUAL

 

1010964

Appendix

 A—S

PECIFICATIONS

P

OWER

 S

PECIFICATIONS

This section describes autoloader AC input voltages and power consumption 

and lists the power cord specifications.

AC I

NPUT

 V

OLTAGES

 

AND

 P

OWER

 C

ONSUMPTION

The autoloader includes an internal power supply that accepts 100 VAC to 

240 VAC at 50 Hz to 60 Hz. The autoloader has automatic AC input voltage 

selection.  The autoloader is capable of continuous operation when the AC 

power experiences intermittent operation, voltage surges, and voltage spikes.

The power consumption of the autoloader varies depending on the function 

being performed. The autoloader consumes a minimum of 20 watts and a 

maximum of 37 watts (AC true power).  Based on the AC true power 

consumption, the autoloader generates between 69 and 127 BTUs per hour.

P

OWER

 C

ORD

 S

PECIFICATIONS

The autoloader is shipped with two power cords:  One for use in the US and 

Canada and one for use in Europe.

The US/Canada power cord is a 2.1-meter (7-foot), three-conductor, 18 AWG 

power cord for 120-volt use.  The power cord has a molded NEMA 5-15P male 

connector on one end, and a molded IEC 320/EN60320 female connector on 

the other end.  The power cord is UL Listed and CSA Certified.

The European power cord is a 2.5-meter (8.2-foot), three-conductor power 

cord for 230 to 250-volt use.  The power cord has a CEE 7 Standard VII, dual 

earthing male connector on one end, and an IEC 320 C13 female connector on 

the other end.  The cordage is CENELEC HD-21.  The power cord is VDE 

approved.

Requirements for International 220 VAC Power Cord

If you plan to use the autoloader in a location other than the US/Canada or 

Europe, you must supply a power cord that meets the following specifications:

!

The power cord must have a grounded attachment plug of the proper type, 

rating, and safety approval for the intended country.

!

The power cord must have an IEC 320/ EN63020 female connector on one 

end.

!

The cordage must be harmonized to CENELEC publication HD-21.  The 

electrical characteristics and rating must be minimum H05VVF3G1.00 (10 A).

Summary of Contents for VXA-2 AUTOPAK1X7









































































































Reviews:

No comments