manualshive.com logo in svg

Exabyte VXA-2 AUTOPAK1X7, Product Manual, Page: 49 / 104

Share
Download
Exabyte VXA-2 AUTOPAK1X7 Product Manual Download Page 49

O

CTOBER

 2002

E

XABYTE

 VXA-2 A

UTO

P

AK1x7

 

A

UTOLOADER

41

R

ESETTING

 

THE

 A

UTOLOADER

 

AND

 T

APE

 D

RIVE

R

ESETTING

 

THE

 A

UTOLOADER

 

AND

 T

APE

 

D

RIVE

  

If the autoloader or tape drive has encountered an error and is still not 

operating after you have tried the recommended corrective action, you may 

need to perform a reset.

To perform a reset, use one of the following methods:

!

Press

 [RESET]

 on the operator panel, then press 

[ENTER]

 at the confirmation 

screen (or press 

[ESCAPE]

 to cancel).  This method resets the autoloader only, 

not the tape drive.

!

Perform a power-on reset by powering the autoloader off and back on.  This 

method resets the autoloader and the tape drive.

When the power-on self-test is complete, the Status screen appears on the 

LCD.

Note:

If the autoloader is performing a cartridge move operation when it is reset, 

it attempts to complete the move operation after it performs the power-on 

self-test.

V

IEWING

 A

UTOLOADER

 

AND

 T

APE

 D

RIVE

 I

NFORMATION

 

The functions in the Autoloader Info Menu and Drive Info Menu are mainly 

for use by Technical Support and application developers. Technical Support 

personnel may ask you to display one of these screens and locate information 

to help troubleshoot a problem.

This section describes the following autoloader and tape drive information:

!

Autoloader code versions.

 Contains information about the autoloader’s 

flash code level and boot code level.

!

Autoloader system statistics. 

Contains information about robot operations.

!

Autoloader system sensors.

 Contains information about the autoloader’s 

mechanical sensors.

!

Autoloader inventory.

 Contains information about the elements.

!

Tape drive status and display information.

  Contains information about the 

tape drive.

Caution

Before resetting the autoloader and tape drive, make sure they are not 

communicating across the SCSI bus.  A reset may disrupt communications on the 

SCSI bus.

Summary of Contents for VXA-2 AUTOPAK1X7









































































































Reviews:

No comments