Exabyte VXA-2 AUTOPAK1X7 Product Manual Download Page 70

Page: 70 / 104

RODUCT

ANUAL

1010964

Chapter

AINTENANCE

PGRADING

THE

APE

RIVE

’

IRMWARE

AND

REATING

IAGNOSTIC

ISTINGS

To upgrade firmware and create diagnostic listings for the VXA-2 tape drive,

download VXA2Tool from www.exabyte.com. VXA2Tool allows you to

upgrade firmware and perform diagnostics over the autoloader’s SCSI bus.

Refer to the readme file provided with the program for installation

instructions. Refer to the program’s online help for instructions on

performing upgrades and diagnostics.

You can download new firmware from www.exabyte.com or you can contact

Exabyte Technical Support for firmware.

Caution

Do not upgrade firmware unless Exabyte Technical Support has advised you to do

so. If performed improperly, the upgrade procedure can render your tape drive

inoperable. Consult with Exabyte Technical Support before performing an

upgrade.

Summary of Contents for VXA-2 AUTOPAK1X7









































































































Search results

Summary of Contents for VXA-2 AUTOPAK1X7

Reviews:

Exabyte VXA-2 AUTOPAK1X7, Product Manual, Page: 70 / 104

Search results

Summary of Contents for VXA-2 AUTOPAK1X7

Reviews: