manualshive.com logo in svg

Exabyte VXA-2 AUTOPAK1X7, Product Manual, Page: 55 / 104

Share
Download
Exabyte VXA-2 AUTOPAK1X7 Product Manual Download Page 55

O

CTOBER

 2002

E

XABYTE

 VXA-2 A

UTO

P

AK1x7

 

A

UTOLOADER

47

V

IEWING

 A

UTOLOADER

 

AND

 T

APE

 D

RIVE

 I

NFORMATION

V

IEWING

 T

APE

 D

RIVE

 S

TATUS

 I

NFORMATION

To view tape drive status information:

1.

1.

1.

1.

Select Drive Info Menu from the Main Menu.

2.

2.

2.

2.

Press 

[ENTER]

 to display the Drive Info Menu. The following screen appears:

3.

3.

3.

3.

If you want to view drive status information, press 

[ENTER]

 to display the 

Drive Status screen.  

Table 4-5

 lists the information displayed on the Drive 

Status screen.

!

D r i v e

S t a t u s

Table 4-5

Tape drive status information 

Status

Description

Type

Displays the type of drive installed.

Serial#

Displays the serial number of the drive.

BootVer 

(Boot Version)

Displays the code level of the drive’s boot ROM.

FlshVer 

(Flash Version)

Displays the code level of the drive’s flash EPROM.

Needs Clean

Indicates whether the drive is clean (0) or needs to be cleaned (1).

Cart St 

(Cartridge Status)

Displays the status of the cartridge, if any, in the drive:

Loaded

 – A cartridge is in the drive and the tape is loaded into the tape path.

Loading

 – A cartridge is being loaded into the drive.

Unloading

 – A cartridge is being unloaded from the drive.

Present

 – A cartridge is in the drive, but the tape is not loaded in the tape path.

Empty

 – The drive does not contain a cartridge.

Format

Displays the data format of the cartridge currently in the drive.

Present

Indicates whether a drive is installed (1) or not (0).

Occupid (Occupied)

Indicates if a cartridge is loaded in the drive (1) or not (0).

OccVald 

(Occupied Valid)

Indicates if the occupied information is reliable (1) or not (0).

Access

Indicates if the drive is accessible to the robot (1) or not (0).

Summary of Contents for VXA-2 AUTOPAK1X7









































































































Reviews:

No comments