manualshive.com logo in svg

Exabyte VXA-2 AUTOPAK1X7, Product Manual, Page: 48 / 104

Share
Download
Exabyte VXA-2 AUTOPAK1X7 Product Manual Download Page 48

40

P

RODUCT

 M

ANUAL

 

1010964

Chapter

 

4

  O

PERATING

 

THE

 A

UTOLOADER

Table 4-1

Tape drive LED states 

Operation

LED 

Pattern

LED #1

LED #2

LED #3

LED #4

Operational Conditions

Power-on self-test

(LEDs illuminate sequentially)a

No tape loaded

Off

Off

Off

Green

SCSI activity; (LED 4 may flash with other LED 

operations)

Off

Off

Off

Flashing 

Green

Tape loading or unloading

Off

Flashing 

Green

Off

Off

Tape ready; idle

Off

Green

Off

Off

Reading

Off

Off

Green

Flashing 

Green

Writing

Off

Off

Yellow

Flashing 

Green

Space forward

Off

Off

Flashing 

Green

Off

Space reverse or rewinding

Flashing 

Green

Off

Off

Off

Cleaning in process

Flashing 

Green

Off

Flashing 

Green

Off

Service Notification

Cleaning required 

Off

Flashing

Yellow

Off

Off

Cleaning tape used up

Off

Flashing 

Green/ Yellow

Off

Off

Recoverable error

b

Yellow

Green

Yellow

Off

Unrecoverable error

b

Yellow

Off

Yellow

Off

Factory service may be required

c

 

(May be illuminated green, yellow, or off.)

Flashing Red

Broken tape

Flashing 

Green/ Yellow

Off

Flashing 

Green/ Yellow

Off

Format recovery

d

Off

Off

Flashing 

Green/ Yellow

Off

Tape path over temperature

e

Off

Off

Off

Orange

Self Tests

Self-test passed

Green

Green

Green

Off

Self-test running

(Fast scrolling green)

Off

Self-test failed

f

 

Yellow

Yellow

Yellow

Off

a

For the power-on self-test, the LEDs scroll sequentially right to left then left to right in yellow and green. LED 4 illuminates in red and green. 
When POST is completed, LED 4 is illuminated in green.

b

Retry the operation. If the problem persists, try power cycling the drive to clear the error. If you cannot resolve the problem 

yourself, contact Exabyte Technical Support.

c

You may need to return the drive for service; contact Exabyte Technical Support.

d

The tape was written without a valid end-of-data mark, which often occurs if you power-down the drive while the drive 

was writing. The tape drive will perform a format recovery, which involves reading the data to determine where the end of 

data is located. This may take as long as 2 to 3 hours.

e

Contact Exabyte Technical Support.

f

If a self-test fails, clean the drive with a VXAtape cleaning cartridge. If the failure still occurs, try a new tape.

Summary of Contents for VXA-2 AUTOPAK1X7









































































































Reviews:

No comments