manualshive.com logo in svg

Exabyte VXA-2 AUTOPAK1X7, Product Manual, Page: 73 / 104

Share
Download
Exabyte VXA-2 AUTOPAK1X7 Product Manual Download Page 73

O

CTOBER

 2002

E

XABYTE

 VXA-2 A

UTO

P

AK1x7

 

A

UTOLOADER

65

T

ROUBLESHOOTING

✔

SCSI adapter card installation.

 Make sure that you installed your SCSI 

adapter card correctly. Refer to the documentation that came with your card 

for installation and troubleshooting instructions. Pay special attention to 

steps describing setting various jumpers and switches on the card. Make sure 

that the card is properly seated.

✔

Software installation.

 Make sure that your application software is installed 

and configured correctly. Refer to the documentation that came with your 

software. Pay special attention to steps describing configuring the software 

for use with the autoloader and drive.

✔

Control mode.

 Make sure the autoloader is operating in the correct control 

mode. For most applications, the control mode should be set to SCSI. See 

page 28

 for more information.

After checking the items above, reset the autoloader as described on 

page 38

.

A

UTOLOADER

 O

PERATION

 P

ROBLEMS

If the autoloader has been successfully operating in the past, but is now 

experiencing problems, check the following:

✔

Control mode

. If you are using an application software package to control 

robot operations, the autoloader must be set to SCSI mode. See 

page 28

 for 

more information. If you are operating the autoloader in Sequential mode, 

see 

page 41

.

✔

Security

. Make sure that security is set correctly for the operation you are 

trying to perform.  If security is enabled, you cannot perform many 

operations on the LCD and you cannot remove the magazine.  Security can 

be enabled from the LCD (see 

page 29

) or from your application software 

with a SCSI command.

✔

Robot operation

. You can use the selections in the Command Menu and the 

Demo Menu to determine if the robot is functioning properly. See 

page 48

.

✔

Firmware level.  

Make sure your autoloader contains the correct versions of 

boot code and firmware.  To check the current code levels, see 

page 42

.  To 

determine whether you have the latest versions, check the Exabyte web site 

at www.exabyte.com.

Summary of Contents for VXA-2 AUTOPAK1X7









































































































Reviews:

No comments