Exabyte VXA-2 AUTOPAK1X7 Product Manual Download Page 79

Page: 79 / 104

CTOBER

2002

XABYTE

VXA-2 A

UTO

AK1x7

UTOLOADER

RROR

ODES

198

CHM full before move

. There

was a cartridge in the robot

before a move operation,

initialize element status, or

diagnostic test.

Remove the magazine and look for anything that might be

obstructing the robot.

Make sure the autoloader is not being used by any host,

then reset the autoloader from the operator panel. If

necessary, power the autoloader off and back on to reset

the tape drive.

If the error persists, contact your service provider. You may

be asked to supply a diagnostic listing, and you may need

new firmware.

199

Remove tape in drive

. The

cartridge must be removed

before the autoloader can begin

its POST.

Remove the cartridge from the tape drive.

210

Remove all tapes for calib

. All

cartridges must be removed so

the autoloader can begin

calibration.

Remove the magazine (it is unlocked).

Remove cartridges from all the magazine slots, the tape

drive, and the picker.

Replace the magazine. The autoloader will automatically

calibrate.

211

Eject sensor error.

There is a

bad sensor or the autoloader

cannot communicate with the

tape drive over the serial

interface and there is a cartridge

protruding from the tape drive.

Make sure the autoloader is not being used by any host,

then reset the autoloader and the tape drive by powering

the autoloader off and back on to reset the tape drive.

If the error persists, contact your service provider.

212

Remove tape in robot.

cartridge was in the robot during

POST.

Remove the magazine (it is unlocked).

Remove the cartridge from the robot and place it in the

magazine (if you know where it goes).

Replace the magazine. The autoloader automatically

resumes post.

Table 6-1

Autoloader error codes (continued)

Code

Description

Corrective action

Summary of Contents for VXA-2 AUTOPAK1X7









































































































Search results

Summary of Contents for VXA-2 AUTOPAK1X7

Reviews:

Exabyte VXA-2 AUTOPAK1X7, Product Manual, Page: 79 / 104

Search results

Summary of Contents for VXA-2 AUTOPAK1X7

Reviews: