manualshive.com logo in svg

Exabyte VXA-2 AUTOPAK1X7, Product Manual, Page: 44 / 104

Share
Download
Exabyte VXA-2 AUTOPAK1X7 Product Manual Download Page 44

36

P

RODUCT

 M

ANUAL

 

1010964

Chapter

 

4

  O

PERATING

 

THE

 A

UTOLOADER

C

LEANING

 

THE

 T

APE

 D

RIVE

Clean the tape drive whenever the autoloader displays 

ClnSoon

 on the Status 

screen or whenever your application software notifies you.  (Not all software 

applications display cleaning requirements.)  Regular cleaning helps ensure 

that the drive functions reliably.  If 

MustCln

 appears on the Status screen, the 

drive will not perform write or read functions until it is cleaned.

Note:

Some software applications automatically perform drive cleaning. If your 

application software supports automatic cleaning, store a cleaning 

cartridge in the magazine slot specified by the application. Refer to the 

documentation for your software.

Follow these steps to clean the tape drive:

1.

1.

1.

1.

Park the robot and remove the magazine, as follows:

a.

a.

a.

a.

From the Main Menu, press  

[

3

]

 or 

[

4

]

  until the following screen appears:

b.

b.

b.

b.

Press 

[ENTER]

. The following message flashes on the screen: 

Unlock Magazine Yes:ENTER No:ESCAPE

 

c.

c.

c.

c.

Press 

[ENTER]

 to unlock the magazine. The robot parks at the top of the 

autoloader and the magazine’s solenoid releases.

d.

d.

d.

d.

Grasp the magazine at the top (near cartridge slot 7) and pull out.

Caution

Do not use any cleaning method other than the VXAtape Cleaning Cartridge (or a 

cleaning cartridge approved by Exabyte for use with VXA drives).  Using other 

cleaning methods may void the tape drive’s warranty.
Do not rewind and reuse the material in a cleaning cartridge.  Reuse may 

redistribute contaminants previously removed from the tape path.  If all cleaning 

material has been used, discard the cartridge and use a new cleaning cartridge.

!

P a r k

&

U n l o c k

Caution

Do not force the magazine out of the autoloader. Doing so may damage the 

magazine or the robot.

Summary of Contents for VXA-2 AUTOPAK1X7









































































































Reviews:

No comments