manualshive.com logo in svg

Exabyte VXA-2 AUTOPAK1X7, Product Manual, Page: 10 / 104

Share
Download
Exabyte VXA-2 AUTOPAK1X7 Product Manual Download Page 10

2

P

RODUCT

 M

ANUAL

 

1010964

Chapter

 

1

  P

RODUCT

 O

VERVIEW

A

UTOLOADER

 F

EATURES

The AutoPak

1x7

 includes the following features:

!

Removable cartridge magazine.

  The autoloader includes a removable 

magazine containing seven storage slots.  The magazine is easily accessible 

from the front of the autoloader.

!

Operator panel with LCD display.

  The operator panel allows you to 

monitor autoloader operations, select configuration options, and control the 

robot.

!

Robotic cartridge handler (robot).

 The robot moves cartridges between 

storage slots and the tape drive. 

!

Wide, low-voltage differential (LVD) SCSI interface.

  The autoloader and 

tape drive each support independent sets of SCSI messages and commands 

and can be connected to an LVD SCSI bus.

!

Tabletop or rack-mount configuration.

  The autoloader is designed as a 

tabletop unit, but can also be mounted in a standard 19-inch rack. If desired, 

you can mount two autoloaders side-by-side on a single rack shelf.  

Rack-mounting kits are available from Exabyte.

Summary of Contents for VXA-2 AUTOPAK1X7









































































































Reviews:

No comments