manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

VII LCD CONTROLLER BLOCK: LCD CONTROLLER

B-VII-2-6

EPSON

S1C33L03 FUNCTION PART

Use the EDMAEN (D3)/LCDC system control register (0x39FFFD) to mask the #DMAREQx signals.

EDMAEN = "1": External DMA requests enabled

EDMAEN = "0": External DMA requests disabled (default)

Use the BREQEN (D2)/LCDC system control register (0x39FFFD) to mask the #BUSREQ signals.

BREQEN = "1": External bus release requests enabled

BREQEN = "0": External bus release requests disabled (default)

Other settings, such as memory specification-related settings, are made using the registers of the BCU and

SDRAM controllers. For details, refer to the description of the respective controllers.

LCD Controller Setting Procedure

Procedure to access the LCDC registers (when using #WAIT signal)

1. A6IO (D9)/access control register (0x48132) = "1"

This sets area 6 so that the internal device will be accessed.

2. A6WT[2:0] (D[A:8])/areas 6–4 setup register (0x4812A) = "000"

This sets area 6 so that it can be accessed with no wait states.

3. SWAITE (D0)/bus control register (0x4812E) = "1"

This enables the #WAIT signal.

4. The LCDC registers can be accessed.

Procedure to enable the LCD panel

1. SEMAS (D2)/bus control register (0x4812E) = "1"

This enables an external bus master.

2. LCDEN (D5)/LCDC mode register 2 (0x39FFE3) = "1"

This enables the LCD controller.

3. CFP3[5:4] (D[5:4])/P3 function select register (0x402DC) = "11"

This sets the P35 pin as the #BUSACK output and the P34 pin as the #BUSREQ input.

4. Initializing the LCDC registers

Setup the LCDC register as necessary except for the look-up table registers (0x39FFF5, 0x39FFF7) as

necessary.

5. LPSAVE[1:0] (D[1:0])/LCDC mode register 2 (0x39FFE3) = "11"

This sets the LCD controller in power save mode to normal operation mode. Wait until the LCD

controller completes the power-up sequence.

6. Setting the look-up table

Setup the look-up table by writing data to the look-up table address register (0x39FFF5) and look-up table

data register (0x39FFF7).

Setting the number of wait states for accessing the LCDC registers (area 6) when

#WAIT signal is disabled

•

 

The LCDC registers except for the look-up table data register (0x39FFF7) should be accessed with 4 wait

states inserted.

•

 

When writing data to the look-up table data register (0x39FFF7), red and green data should be written

with 4 wait states inserted (1st and 2nd writes in a sequence), and blue data should be written with 7 wait

states inserted (last write in a sequence).

Use 

A6WT[2:0] (D[A:8])/areas 6–4 setup register (0x4812A) to set the number of wait states to

 be inserted

when area

 6 is accessed.

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Brand: 3Com Pages: 8
Western Digital Scorpio WD2500BPVT Product Specifications preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 3
Western Digital Scorpio WD2500BPVT Product Features preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 4
National Instruments Fieldpoint cFP-RTD-124 Operating Instructions Manual preview
Fieldpoint cFP-RTD-124
Brand: National Instruments Pages: 15
ZALMAN ZM-WB2 Gold User Manual preview
ZM-WB2 Gold
Brand: ZALMAN Pages: 9
Garland INT40G2SR44 User Manual preview
INT40G2SR44
Brand: Garland Pages: 43
Rolls HR11C - SCHEMA Wiring Diagram preview
HR11C - SCHEMA
Brand: Rolls Pages: 1
ICOP Technology BF01 User Manual preview
BF01
Brand: ICOP Technology Pages: 34
Accusys ACS-7630 User Manual preview
ACS-7630
Brand: Accusys Pages: 34
ZALMAN ZM80C-HP Manual preview
ZM80C-HP
Brand: ZALMAN Pages: 18
Corsair H80i v2 Quick Start Manual preview
H80i v2
Brand: Corsair Pages: 12
El.Mo 090010932 User Manual preview
090010932
Brand: El.Mo Pages: 16
MESA Electronic 4C24 Manual preview
4C24
Brand: MESA Electronic Pages: 27
National Instruments PXI-GPIB Getting Started preview
PXI-GPIB
Brand: National Instruments Pages: 45
Inter-m S- Media Manual preview
S- Media
Brand: Inter-m Pages: 20
Apposite Technologies Linktropy MINI-G User Manual preview
Linktropy MINI-G
Brand: Apposite Technologies Pages: 57
Corsair H100i Manual preview
H100i
Brand: Corsair Pages: 134
OWC ENVOY PRO MINI User Manual preview
ENVOY PRO MINI
Brand: OWC Pages: 7

Brands by name

Popular brands

Load more brands