manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

V DMA BLOCK: HSDMA (High-Speed DMA)

S1C33L03 FUNCTION PART

EPSON

B-V-2-33

A-1

B-V

HSDMA

S0ADRL15–S0ADRL0:

Ch.  0  source address[15:0]
(D[F:0]) / Ch. 0 low-order source address set-up register (0x48224)

S0ADRH11–S0ADRH0: Ch.  0  source address[27:16]

(D[B:0]) / Ch. 0 high-order source address set-up register (0x48226)

S1ADRL15–S1ADRL0:

Ch.  1  source address[15:0]
(D[F:0]) / Ch. 1 low-order source address set-up register (0x48234)

S1ADRH11–S1ADRH0: Ch.  1  source address[27:16]

(D[B:0]) / Ch. 1 high-order source address set-up register (0x48236)

S2ADRL15–S2ADRL0:

Ch.  2  source address[15:0]
(D[F:0]) / Ch. 2 low-order source address set-up register (0x48244)

S2ADRH11–S2ADRH0: Ch.  2  source address[27:16]

(D[B:0]) / Ch. 2 high-order source address set-up register (0x48246)

S3ADRL15–S3ADRL0:

Ch.  3  source address[15:0]
(D[F:0]) / Ch. 3 low-order source address set-up register (0x48254)

S3ADRH11–S3ADRH0: Ch.  3  source address[27:16]

(D[B:0]) / Ch. 3 high-order source address set-up register (0x48256)

In dual-address mode, these bits are used to specify a source address. In single-address mode, an external memory

address at the destination or source of transfer is specified.

Use SxADRL to set the 16 low-order bits of the address and SxADRH to set the 12 high-order bits.

Be sure to disable DMA transfers (HSx_EN = "0") before writing or reading to and from these registers.

The address is incremented or decremented (as set by SxIN) according to the transfer data size each time a DMA

transfer in the corresponding channel is performed.

At initial reset, these bits are not initialized.

D0ADRL15–D0ADRL0: Ch.  0  destination address[15:0]

(D[F:0]) / Ch. 0 low-order destination address set-up register (0x48228)

D0ADRH11–D0ADRH0: Ch.  0  destination address[27:16]

(D[B:0]) / Ch. 0 high-order destination address set-up register (0x4822A)

D1ADRL15–D1ADRL0: Ch.  1  destination address[15:0]

(D[F:0]) / Ch. 1 low-order destination address set-up register (0x48238)

D1ADRH11–D1ADRH0: Ch.  1  destination address[27:16]

(D[B:0]) / Ch. 1 high-order destination address set-up register (0x4823A)

D2ADRL15–D2ADRL0: Ch.  2  destination address[15:0]

(D[F:0]) / Ch. 2 low-order destination address set-up register (0x48248)

D2ADRH11–D2ADRH0: Ch.  2  destination address[27:16]

(D[B:0]) / Ch. 2 high-order destination address set-up register (0x4824A)

D3ADRL15–D3ADRL0: Ch.  3  destination address[15:0]

(D[F:0]) / Ch. 3 low-order destination address set-up register (0x48258)

D3ADRH11–D3ADRH0: Ch.  3  destination address[27:16]

(D[B:0]) / Ch. 3 high-order destination address set-up register (0x4825A)

In dual-address mode, these bits are used to specify a destination address. In single-address mode, these bits are not

used.

Be sure to disable DMA transfers (HSx_EN = "0") before writing or reading to and from these registers.

The address is incremented or decremented (as set by DxIN) according to the transfer data size each time a DMA

transfer in the corresponding channel is performed.

At initial reset, these bits are not initialized.

PHSD0L2–PHSD0L0: Ch. 0 interrupt level (D[2:0]) / HSDMA Ch. 0/1 interrupt priority register (0x40263)
PHSD1L2–PHSD1L0: Ch. 1 interrupt level (D[6:4]) / HSDMA Ch. 0/1 interrupt priority register (0x40263)
PHSD2L2–PHSD2L0: Ch. 2 interrupt level (D[2:0]) / HSDMA Ch. 2/3 interrupt priority register (0x40264)
PHSD3L2–PHSD3L0: Ch. 3 interrupt level (D[6:4]) / HSDMA Ch. 2/3 interrupt priority register (0x40264)

Set the priority level of an end-of-DMA interrupt in the range of 0 to 7.

At initial reset, these registers become indeterminate.

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

A10 Thunder Series Manual preview
Thunder Series
Brand: A10 Pages: 52
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Brand: Renesas Pages: 6
Supermicro SuperServer 5019S-L User Manual preview
SuperServer 5019S-L
Brand: Supermicro Pages: 61
Time domain PulsON 440 Datasheet And User Manual preview
PulsON 440
Brand: Time domain Pages: 64
Lanner ICS-P570 User Manual preview
ICS-P570
Brand: Lanner Pages: 63
Digi ConnectCore 8X Hardware Reference Manual preview
ConnectCore 8X
Brand: Digi Pages: 116
MICROENER IM30-CV Operation Manual preview
IM30-CV
Brand: MICROENER Pages: 24
ENERMAX LIQMAX III ELC-LMT120-ARGB User Manual preview
LIQMAX III ELC-LMT120-ARGB
Brand: ENERMAX Pages: 32
Accusys ACS-7630 User Manual preview
ACS-7630
Brand: Accusys Pages: 34
Sony Ericsson GC79 User Manual preview
GC79
Brand: Sony Ericsson Pages: 93
Inspired Energy ATA004N Operating Instructions preview
ATA004N
Brand: Inspired Energy Pages: 5
SIIG US2273 Quick Installation Manual preview
US2273
Brand: SIIG Pages: 8
Idis DR-8416 Quick Manual preview
DR-8416
Brand: Idis Pages: 40
Intel NetStructure ZT 5085 Manual preview
NetStructure ZT 5085
Brand: Intel Pages: 106
ZALMAN CNPS9700 LED User Manual preview
CNPS9700 LED
Brand: ZALMAN Pages: 8
MACHINIST X79-Z9-D7 User Manual preview
X79-Z9-D7
Brand: MACHINIST Pages: 15
peplink Balance 380 User Manual preview
Balance 380
Brand: peplink Pages: 111

Brands by name

Popular brands

Load more brands