manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

V DMA BLOCK: IDMA (Intelligent DMA)

S1C33L03 FUNCTION PART

EPSON

B-V-3-17

A-1

B-V

IDMA

Programming Notes

 (1) Before setting the IDMA base address, be sure to disable DMA transfers (IDMAEN = "0"). Writing to the

IDMA base address register is ignored when the DMA transfer is enabled (IDMAEN = "1"). Also, when the

register is read during a DMA transfer, the data is indeterminate. When setting or rewriting control

information for each channel, make sure that DMA transfers will not occur in any channel.

 (2) The address that is set in the IDMA base address register must always be a word (32-bit) boundary address.

 (3) After an initial reset, the interrupt factor flag (FIDMA) becomes indeterminate. To prevent unwanted

interrupts from occurring, be sure to reset the flag in a program.

 (4) Once an interrupt occurs, be sure to reset the interrupt factor flag (FIDMA) before setting up the PSR again or

executing the reti instruction. This ensures that an interrupt will not be generated for the same factor.

 (5) If all the following conditions are met, the transfer counter value becomes invalid during IDMA transfer so

data cannot be transferred properly.

1. The IDMA control information (source/destination addresses, transfer counter, etc.) is placed in the

external EDO DRAM.

2. The DRAM access timing condition is set to EDO mode by the BCU register.

3. The bus clock is set to x2 speed mode (#X2SPD pin = "0").

When placing the control information in the EDO DRAM in x2 speed mode, the DRAM access timing

condition must be set to high-speed page mode.

Or place the control information in the internal RAM. Using the internal RAM increases the performance

because the overhead during IDMA transfer is decreased to 6 cycles on both load/store operations.

 (6) In HALT mode, since the DMA and BCU clocks operate, if the next operation is performed in HALT mode,

not HALT2 mode, with a setting of 0 in clock option register HLT2OP (D3/0x40190), that operation will be

an unpredictable erroneous operation.

If a DMA trigger occurs and DMA is invoked while the CPU is stopped after HALT mode execution,

erroneous operation will result. Ensure that DMA is not invoked in HALT mode.

In HALT2 mode, DMA is not invoked since the DMA and BCU clocks are stopped.

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

Canon C50FSi - VB Network Camera Setup Manual preview
C50FSi - VB Network Camera
Brand: Canon Pages: 32
Rabbit 2000 Reference Manual preview
2000
Brand: Rabbit Pages: 120
D-Link DFE-690TXD Quick Install Manual preview
DFE-690TXD
Brand: D-Link Pages: 12
IBM AS/400 Hardware User Manual preview
AS/400
Brand: IBM Pages: 104
IBM System Storage TS3100 Setup, Operator, And Service Manual preview
System Storage TS3100
Brand: IBM Pages: 375
Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
ZALMAN ZM-MFC1 Combo User Manual preview
ZM-MFC1 Combo
Brand: ZALMAN Pages: 7
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Brand: EMS Pages: 52
Omron JUSP-NS500 Datasheet preview
JUSP-NS500
Brand: Omron Pages: 6
ATI Technologies RADEON 9800 PRO Getting Started Manual preview
RADEON 9800 PRO
Brand: ATI Technologies Pages: 20
Extron electronics VERSATOOLS MTP User Manual preview
VERSATOOLS MTP
Brand: Extron electronics Pages: 19
SIIG US2273 Quick Installation Manual preview
US2273
Brand: SIIG Pages: 8
ADLINK Technology EOS-1200 User Manual preview
EOS-1200
Brand: ADLINK Technology Pages: 108
Behringer X-MADI Quick Start Manual preview
X-MADI
Brand: Behringer Pages: 15
Link electronics Analog Pulse Generator 812-OP/H Specification Sheet preview
Analog Pulse Generator 812-OP/H
Brand: Link electronics Pages: 2
Adaptec 2025ZCR - SCSI RAID Storage Controller Datasheet preview
2025ZCR - SCSI RAID Storage Controller
Brand: Adaptec Pages: 2

Brands by name

Popular brands

Load more brands