manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

III PERIPHERAL BLOCK: 8-BIT PROGRAMMABLE TIMERS

B-III-3-2

EPSON

S1C33L03 FUNCTION PART

Uses of 8-Bit Programmable Timers

The down-counter of the 8-bit programmable timer cyclically outputs an underflow signal according to the preset

data that is set in the software. This underflow signal is used to generate an interrupt request to the CPU or to

control the internal peripheral circuits. In addition, this signal can be output to external devices.

Furthermore, each 8-bit programmable timer generates a clock from the underflow signal by dividing it by 2, and

the resulting clock is output to a specific internal peripheral circuit.

CPU interrupt request/IDMA invocation request

Each timer's underflow condition can be used as an interrupt factor to output an interrupt request to the CPU.

Therefore, an interrupt can be generated at an interval that is set in the software.

This interrupt factor also can be used to invoke IDMA or HSDMA.

Clock output to external devices

The underflow signal can be output from the chip to the outside. This output can be used to control external

devices. The output pins of each timer are described in the preceding section.

Control of and clock supply to internal peripheral circuits

The following describes the functions controlled by the underflow signal from the 8-bit programmable timer

and the internal peripheral circuits that use the timer's output clock.

8-bit programmable timer 0
 • DRAM refresh

When the BCU has a DRAM directly connected to its external bus, the underflow signal from timer 0

can be used as a DRAM refresh request signal. This enables the intervals of the refresh cycle to be

programmed.

To use this function, write "1" to the BCU's control bit RPC2 (D9) / Bus control register (0x4812E) to

enable the DRAM refresh.

 • A/D conversion start trigger

The A/D converter enables a trigger for starting the A/D conversion to be selected from among four

available types. One of these is the underflow signal of the 8-bit programmable timer 0. This makes it

possible to perform the A/D conversion at programmable intervals.

To use this function, write "10" to the A/D converter control bit TS[1:0] (D[4:3]) / A/D trigger register

(0x40242) to select the 8-bit programmable timer 0 as the trigger.

8-bit programmable timer 1
 • Oscillation stabilization wait time of the high-speed (OSC3) oscillation circuit

When SLEEP mode is cleared by an external interrupt, the high-speed (OSC3) oscillation circuit starts

oscillating. To prevent the CPU from being operated erratically by an unstable clock before the

oscillation stabilizes, the C33 Core Block enables setting of the waiting time before the CPU starts

operating after SLEEP is cleared. Use the 8-bit programmable timer 1 to generate this waiting time. If the

8-bit programmable timer 1 is set so that the timer is actuated when the high-speed (OSC3) oscillation

circuit starts oscillating the timer and, after the oscillation stabilization time elapses, an underflow signal

is generated, then the CPU can be started up by that underflow signal.

To use this function, write "0" to the oscillation circuit control bit 8T1ON (D2) / Clock option register

(0x40190) to enable the oscillation stabilization waiting function.

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

National Instruments USB-6501 Quick Start preview
USB-6501
Brand: National Instruments Pages: 5
National Instruments PXIe-8106 User Manual preview
PXIe-8106
Brand: National Instruments Pages: 76
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Brand: Parker Pages: 107
Renesas R0E530650CFJ30 User Manual preview
R0E530650CFJ30
Brand: Renesas Pages: 4
Dataprobe iBoot-Exp Manual preview
iBoot-Exp
Brand: Dataprobe Pages: 5
KonNad SinoCon C2000-C2-SHK0401-BB1 User Manual preview
SinoCon C2000-C2-SHK0401-BB1
Brand: KonNad Pages: 12
Renesas R0E0144TNPFK00 User Manual preview
R0E0144TNPFK00
Brand: Renesas Pages: 4
ADS Technologies PTV-370 Driver Manual preview
PTV-370
Brand: ADS Technologies Pages: 1
CSL 300295 User Manual preview
300295
Brand: CSL Pages: 24
FOR-A USF-105PS Operation Manuals preview
USF-105PS
Brand: FOR-A Pages: 37
HighPoint NA381TB Quick Installation Manual preview
NA381TB
Brand: HighPoint Pages: 3
Tektronix 7B87 Instruction Manual preview
7B87
Brand: Tektronix Pages: 143
b&t RTL8720D Instruction Manual preview
RTL8720D
Brand: b&t Pages: 34
YTTEK Y.FORCE YTPC400 Quick Start Manual preview
Y.FORCE YTPC400
Brand: YTTEK Pages: 26
Addi-Data MSX-E Series Technical Description preview
MSX-E Series
Brand: Addi-Data Pages: 20
abaco systems PEX430 Hardware Reference Manual preview
PEX430
Brand: abaco systems Pages: 51
Emerson dixell Quick Start Manual preview
dixell
Brand: Emerson Pages: 8
Emerson Liebert NXL 250 Installation Manual preview
Liebert NXL 250
Brand: Emerson Pages: 36

Brands by name

Popular brands

Load more brands