manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

TABLE OF CONTENTS

iv

EPSON

S1C33L03 TECHNICAL MANUAL

Bus Clock .................................................................................................................................. B-II-4-17

Bus Speed Mode .......................................................................................................... B-II-4-18
Bus Clock Output .......................................................................................................... B-II-4-18

Bus Cycles in External System Interface................................................................................. B-II-4-19

SRAM Read Cycles ...................................................................................................... B-II-4-19
Bus Timing .................................................................................................................... B-II-4-20
SRAM Write Cycles ...................................................................................................... B-II-4-21
Burst ROM Read Cycles .............................................................................................. B-II-4-23

DRAM Direct Interface.............................................................................................................. B-II-4-24

Outline of DRAM Interface............................................................................................ B-II-4-24
DRAM Setting Conditions ............................................................................................. B-II-4-25
DRAM Read/Write Cycles ............................................................................................ B-II-4-28
DRAM Refresh Cycles.................................................................................................. B-II-4-31

Releasing External Bus ............................................................................................................ B-II-4-32
Power-down Control by External Device ................................................................................. B-II-4-33
I/O Memory of BCU .................................................................................................................. B-II-4-34

II-5 ITC (Interrupt Controller).............................................................................................B-II-5-1

Outline of Interrupt Functions..................................................................................................... B-II-5-1

Maskable Interrupts ........................................................................................................ B-II-5-1
Interrupt Factors and Intelligent DMA ............................................................................ B-II-5-3
Nonmaskable Interrupt (NMI) ......................................................................................... B-II-5-3
Interrupt Processing by the CPU.................................................................................... B-II-5-3
Clearing Standby Mode by Interrupts............................................................................. B-II-5-3

Trap Table................................................................................................................................... B-II-5-4
Control of Maskable Interrupts ................................................................................................... B-II-5-5

Structure of the Interrupt Controller................................................................................ B-II-5-5
Processor Status Register (PSR)................................................................................... B-II-5-5
Interrupt Factor Flag and Interrupt Enable Register...................................................... B-II-5-6
Interrupt Priority Register and Interrupt Levels .............................................................. B-II-5-8

IDMA Invocation ......................................................................................................................... B-II-5-9
HSDMA Invocation ................................................................................................................... B-II-5-11
I/O Memory of Interrupt Controller ........................................................................................... B-II-5-12
Programming Notes.................................................................................................................. B-II-5-25

II-6 CLG (Clock Generator)................................................................................................B-II-6-1

Configuration of Clock Generator .............................................................................................. B-II-6-1
I/O Pins of Clock Generator ....................................................................................................... B-II-6-2
High-Speed (OSC3) Oscillation Circuit...................................................................................... B-II-6-2
PLL ............................................................................................................................................ B-II-6-3
Controlling Oscillation................................................................................................................. B-II-6-3
Setting and Switching Over the CPU Operating Clock ............................................................. B-II-6-4
Power-Control Register Protection Flag .................................................................................... B-II-6-5
Operation in Standby Mode ....................................................................................................... B-II-6-5
I/O Memory of Clock Generator ................................................................................................. B-II-6-6
Programming Notes.................................................................................................................... B-II-6-9

II-7 DBG (Debug Unit).........................................................................................................B-II-7-1

Debug Circuit .............................................................................................................................. B-II-7-1
I/O Pins of Debug Circuit............................................................................................................ B-II-7-1

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

T&D RTR-50 User Manual preview
RTR-50
Brand: T&D Pages: 122
KEMP Technologies LoadMaster 1500 Installation And Configuration Manual preview
LoadMaster 1500
Brand: KEMP Technologies Pages: 71
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Brand: Zhone Pages: 114
JUMO iTRON B 70.2040 Operating Instructions Manual preview
iTRON B 70.2040
Brand: JUMO Pages: 41
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4
Digital Voice Systems VC-20-MR2 User Manual preview
VC-20-MR2
Brand: Digital Voice Systems Pages: 32
Omega Engineering BNC-08DI, BNC-16DI, BNC-16SE User Manual preview
BNC-08DI, BNC-16DI, BNC-16SE
Brand: Omega Engineering Pages: 25
Zoltrix Audio Plus 3200 Hardware Manual preview
Audio Plus 3200
Brand: Zoltrix Pages: 34
Extron electronics Network Device PIP 444 User Manual preview
Network Device PIP 444
Brand: Extron electronics Pages: 62
Cabletron Systems CSMIM-T1 Installation Manual preview
CSMIM-T1
Brand: Cabletron Systems Pages: 198
Zte MC315 User Manual preview
MC315
Brand: Zte Pages: 29
W2IHY EQplus Operating Manual preview
EQplus
Brand: W2IHY Pages: 21
3Com 3C3FEM656C - Megahertz 10/100 LAN+56K Global Modem Quick Start Manual preview
3C3FEM656C - Megahertz 10/100 LAN+56K Global Modem
Brand: 3Com Pages: 53
Paradyne 9126 User Manual preview
9126
Brand: Paradyne Pages: 470
F5 Herculon SSL Orchestrator Setup preview
Herculon SSL Orchestrator
Brand: F5 Pages: 58
Ebyte E810-TTL-CAN01 User Manual preview
E810-TTL-CAN01
Brand: Ebyte Pages: 32
Advantech EKI-6331AN-BE User Manual preview
EKI-6331AN-BE
Brand: Advantech Pages: 72
Polon-Alfa EKS-4001 Installation And Maintenance Manual preview
EKS-4001
Brand: Polon-Alfa Pages: 11

Brands by name

Popular brands

Load more brands