manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

III PERIPHERAL BLOCK: SERIAL INTERFACE

S1C33L03 FUNCTION PART

EPSON

B-III-8-19

A-1

B-III

SIF

Note: The  receive operation is terminated when the first stop bit is sampled even if the stop bit is

configured with two bits.

• Successive receive operations

When the data received in the shift register is transferred to the receive data register, RDBFx is set to "1"

(buffer full), indicating that the received data can be read out. Thereafter, data can be received successively

because the receive data register can be read out while the next data is received. The procedure for receiving

is described above.

When RDBFx is set to "1", a receive-data full interrupt factor occurs. Since an interrupt can be generated as

set by the interrupt controller, the received data can be read using an interrupt processing routine. In addition,

since this interrupt factor can be used to invoke IDMA, the received data can be received successively in

locations prepared in memory through DMA transfers.

For details on how to control interrupts and IDMA requests, refer to "Serial Interface Interrupts and DMA".

 (3) Receive errors

Three types of receive errors can be detected when receiving data in the asynchronous mode.

Since an interrupt can be generated by setting the interrupt controller, the error can be processed using an

interrupt processing routine. For details on receive error interrupts, refer to "Serial Interface Interrupts and

DMA".

• Parity error

If EPRx is set to "1" (parity added), the parity is checked when data is received.

This parity check is performed when the data received in the shift register is transferred to the receive data

register in order to check conformity with PMDx settings (odd or even parity). If any nonconformity is found

in this check, a parity error is assumed and the parity error flag is set to "1".

Ch.0 parity error flag: PER0 (D3) / Serial I/F Ch.0 status register (0x401E2)

Ch.1 parity error flag: PER1 (D3) / Serial I/F Ch.1 status register (0x401E7)

Ch.2 parity error flag: PER2 (D3) / Serial I/F Ch.2 status register (0x401F2)

Ch.3 parity error flag: PER3 (D3) / Serial I/F Ch.3 status register (0x401F7)

Even when this error occurs, the received data in error is transferred to the receive data register and the

receive operation is continued. However, the content of the received data for which a parity error is flagged

cannot be guaranteed.

The PERx flag is reset to "0" by writing "0".

• Framing error

If data with a stop bit = "0" is received, the serial interface assumes that the data is out of synchronization and

generates a framing error.

If two stop bits are used, only the first stop bit is checked.

When this error occurs, the framing-error flag is set to "1".

Ch.0 framing-error flag: FER0 (D4) / Serial I/F Ch.0 status register (0x401E2)

Ch.1 framing-error flag: FER1 (D4) / Serial I/F Ch.1 status register (0x401E7)

Ch.2 framing-error flag: FER2 (D4) / Serial I/F Ch.2 status register (0x401F2)

Ch.3 framing-error flag: FER3 (D4) / Serial I/F Ch.3 status register (0x401F7)

Even when this error occurs, the received data in error is transferred to the receive data register and the

receive operation is continued. However, the content of the received data for which a framing error is flagged

cannot be guaranteed, even if no framing error is found in the following data received.

The FERx flag is reset to "0" by writing "0".

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

Yamaha EMP100 Supplementary Manual preview
EMP100
Brand: Yamaha Pages: 4
Lantronix SISPM1040-582-LRT Quick Start Manual preview
SISPM1040-582-LRT
Brand: Lantronix Pages: 2
Lantronix SDS1101 Quick Start Manual preview
SDS1101
Brand: Lantronix Pages: 7
Octavo OSD3358-SM-RED Getting Started Manual preview
OSD3358-SM-RED
Brand: Octavo Pages: 28
Obihai OBi110 Quick Start Manual preview
OBi110
Brand: Obihai Pages: 2
PaloAlto Networks PA-7500 Quick Start Manual preview
PA-7500
Brand: PaloAlto Networks Pages: 3
Ubiquiti U5-24-500W Quick Start Manual preview
U5-24-500W
Brand: Ubiquiti Pages: 23
Renesas Asynchronous SH7145F Application Note preview
Asynchronous SH7145F
Brand: Renesas Pages: 17
Enterasys X-Pedition 2000 Getting Started Manual preview
X-Pedition 2000
Brand: Enterasys Pages: 86
ACTi GNR-310 Quick Installation Manual preview
GNR-310
Brand: ACTi Pages: 12
ZALMAN CNPS11X Extreme User Manual preview
CNPS11X Extreme
Brand: ZALMAN Pages: 12
ZALMAN CNPS7000C Series User Manual preview
CNPS7000C Series
Brand: ZALMAN Pages: 8
Eurotech Zypad WL15 Series Quick Start preview
Zypad WL15 Series
Brand: Eurotech Pages: 2
Nvidia GEFORCE RTX 4090 Quick Start Manual preview
GEFORCE RTX 4090
Brand: Nvidia Pages: 160
Navitar 1-62643 Dimensional Drawing preview
1-62643
Brand: Navitar Pages: 1
Beckhoff EK1122 Documentation preview
EK1122
Brand: Beckhoff Pages: 84
Freescale Semiconductor KW2xD Series Reference Manual preview
KW2xD Series
Brand: Freescale Semiconductor Pages: 42
Grizzly PSJ-VZ58 gen3 OEM User Manual preview
PSJ-VZ58 gen3 OEM
Brand: Grizzly Pages: 12

Brands by name

Popular brands

Load more brands