Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 Technical Manual Download Page 525 | Manualshive

Page: 525 / 631

background image

VI SDRAM CONTROLLER BLOCK: SDRAM INTERFACE

S1C33L03 FUNCTION PART

EPSON

B-VI-2-29

A-1

B-VI

SDRAM

SDRBA: Number of SDRAM banks (D1) / SDRAM address configuration register (0x39FFC2)

Set the number of banks of the SDRAM.

Write "1": 4 banks

Write "0": 2 banks

Read: Valid

Set "1" when a SDRAM configured with 4 banks is used or set "0" when a SDRAM configured with 2 banks is
used.

The contents set here are applied to all of areas 7, 8, 13, and 14 that are set for SDRAM.
At cold start, SDRBA is set to "0" (2 banks). At hot start, SDRBA retains its status before being initialized.

SDRCL1–SDRCL0: SDRAM CAS latency (D[6:5]) / SDRAM mode set-up register (0x39FFC3)

Set the CAS latency of the SDRAM.

Table 2.17 Setting CAS Latency

SDRCL1

SDRCL0

CAS latency (number of clocks)

1

0

2

Other settings

Not allowed

The SDRAM controller does not support CAS latencies other than 2.

At cold start, SDRCL is set to "11". Be sure to reset to "10" so that the CAS latency is set to 2. At hot start, SDRCL

retain its status before being initialized.

SDRBL1–SDRBL0: SDRAM burst length (D[3:2]) / SDRAM mode set-up register (0x39FFC3)

Set the burst read length of the SDRAM.

Table 2.18 Setting Burst Length

SDRBL1

SDRBL0

Burst length (word)

0

0

1

0

1

2

1

0

4

1

1

8

The SDRAM controller does not support burst write, so the set burst length is effective only for read cycles.

At cold start, SDRBL is set to "11" (8). At hot start, SDRBL retain its status before being initialized.

SDRTRAS2–SDRTRAS0: SDRAM t

RAS

spec (D[7:5]) / SDRAM timing set-up register 1 (0x39FFC4)

Set the t

RAS

SDRAM parameter (ACTIVE to PRECHARGE command period).

In accordance with the specifications of the SDRAM, specify this parameter in terms of the number of SDRAM

clock cycles. Specifying 1–7 sets the period to 1–7 clock cycles. Specifying 0 sets the period to 8 clock cycles.

At cold start, SDRTRAS is set to "000" (8). At hot start, SDRTRAS retain its status before being initialized.

SDRTRP1–SDRTRP0: SDRAM t

RP

spec (D[4:3]) / SDRAM timing set-up register 1 (0x39FFC4)

Set the t

RP

SDRAM parameter (PRECHARGE command period).

In accordance with the specifications of the SDRAM, specify this parameter in terms of the number of SDRAM

clock cycles. Specifying 1–3 sets the period to 1–3 clock cycles. Specifying 0 sets the period to 4 clock cycles.

At cold start, SDRTRP is set to "00" (4). At hot start, SDRTRP retain its status before being initialized.

SDRTRC2–SDRTRC0: SDRAM t

RC

spec (D[2:0]) / SDRAM timing set-up register 1 (0x39FFC4)

Set the t

RC

SDRAM parameter (ACTIVE to ACTIVE command period).

In accordance with the specifications of the SDRAM, specify this parameter in terms of the number of SDRAM

clock cycles. Specifying 1–7 sets the period to 1–7 clock cycles. Specifying 0 sets the period to 8 clock cycles.

At cold start, SDRTRC is set to "000" (8). At hot start, SDRTRC retain its status before being initialized.

Note: When the auto-refresh command is executed, the following command may be issued 3 or 4

CPU_CLK cycles from that point regardless of the t

RC

value set in the SDRTRC register.

Therefore, use SDRAMs with 75 ns or less of t

RC

.

«
...
523
524
525
526
527
...
»

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

Brand: GE Pages: 4

Brand: B2 Pages: 52

Brand: IBA Pages: 29

FRDM-STBC-SA9500

Brand: Freescale Semiconductor Pages: 2

Brand: Genie Pages: 15

IntroSpect Analyzer 2 Series

Brand: Aruba Pages: 5

Brand: T.A Pages: 11

HHM Series HHM2411

Brand: TDK Pages: 2

PISO-725 Series

Brand: ICP DAS USA Pages: 8

Brand: SSV Embedded Systems Pages: 17

PowerBeam PBE-5AC-400-ISO

Brand: Ubiquiti Pages: 23

Brand: ICP DAS USA Pages: 8

Brand: Penguin Edge Pages: 2

cPCIS-1100 Series

Brand: ADLINK Technology Pages: 48

Brand: McIntosh Pages: 44

Brand: Freescale Semiconductor Pages: 42

Quark SoC X1000

Brand: Galileo Pages: 20

Safeguard for Privileged Sessions 3000

Brand: One Identity Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands