manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

II CORE BLOCK: ITC (Interrupt Controller)

S1C33L03 FUNCTION PART

EPSON

B-II-5-19

A-1

B-II

ITC

Fxxx: Interrupt factor flag

Indicate the status of interrupt factors generated.

When read

Read "1": Interrupt factor generated

Read "0": No interrupt factor generated

When written using the reset-only method (default)

Write "1": Factor flag is reset

Write "0": Invalid

When written using the read/write method

Write "1": Factor flag is set

Write "0": Factor flag is reset

The interrupt factor flag is set to "1" when an interrupt factor occurs in each peripheral circuit.

If the following conditions are met at this time, an interrupt is generated to the CPU:

1. The corresponding bit of the interrupt enable register is set to "1".

2. No other interrupt request of higher priority has occurred.

3. The IE bit of the PSR is set to "1" (interrupt enabled).

4. The corresponding interrupt priority register is set to a level higher than the CPU's interrupt level (IL).

When using an interrupt factor to request IDMA, note that even when the above conditions are met, no interrupt

request to the CPU is generated for the interrupt factor that has occurred. If interrupts are enabled at the setting of

IDMA, an interrupt is generated under the above conditions after the data transfer by IDMA is completed.

The interrupt factor flag is always set to "1" when an interrupt factor occurs no matter how the interrupt enable and

interrupt priority registers are set.

In order for the next interrupt to be accepted after interrupt generation, the interrupt factor flag must be reset and

the PSR must be set up again (by setting the IL below the level indicated by the interrupt priority register and

setting the IE bit to "1" or executing the reti instruction).

The interrupt factor flag can only be reset by a write instruction in the software application. If the PSR is again set

up to accept interrupts (or the reti instruction is executed) without resetting the interrupt factor flag, the same

interrupt may occur again. Note also that the value to be written to reset the flag is "1" when using the reset-only

method (RSTONLY = "1") and "0" when using the read/write method (RSTONLY = "0"). Be careful not to

confuse these two conditions.

The interrupt factor flag becomes indeterminate when initially reset, so be sure to reset the flag in the software

application.

Rxxx: IDMA request register

Specify whether or not to invoke IDMA when an interrupt factor occurs.

When using the set-only method (default)

Write "1": IDMA request

Write "0": Not changed

Read: Valid

When using the read/write method

Write "1": IDMA request

Write "0": Interrupt request

Read: Valid

If a bit of this register is set to "1", IDMA is invoked when the corresponding interrupt factor occurs and the

programmed data transfer is performed. If the register bit is set to "0", regular interrupt processing is performed,

without ever invoking IDMA.

For details about IDMA, refer to "IDMA (Intelligent DMA)".

If interrupts are enabled on the IDMA side and the transfer counter reaches the terminal count of 0 after completion

of DMA transfer, the IDMA request register is reset to "0" and an interrupt request for the interrupt factor that

enabled IDMA invoking is generated.

After an initial reset, this register is set to "0" (Interrupt is requested).

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

Yaesu FT-817 - Modification Instructions preview
FT-817 -
Brand: Yaesu Pages: 2
ForeScout CounterACT Quick Installation Manual preview
CounterACT
Brand: ForeScout Pages: 28
IEI Technology PulM-1G4T-I211 Quick Installation Manual preview
PulM-1G4T-I211
Brand: IEI Technology Pages: 2
Xantech CC62 Installation Instructions preview
CC62
Brand: Xantech Pages: 5
Arctic Accelero TWIN TURBO II Installation Manual preview
Accelero TWIN TURBO II
Brand: Arctic Pages: 2
Digital Audio Corporation PCAP II User Manual preview
PCAP II
Brand: Digital Audio Corporation Pages: 164
Renesas Protection Board R0E330850ACBP0 User Manual preview
Protection Board R0E330850ACBP0
Brand: Renesas Pages: 8
YASKAWA CP 040 RS422/485 Manual preview
CP 040 RS422/485
Brand: YASKAWA Pages: 87
Williams Sound DW SY 1 User Manual preview
DW SY 1
Brand: Williams Sound Pages: 2
Axtrinet APG200 User Manual preview
APG200
Brand: Axtrinet Pages: 49
TERSUS Precis-BX305 Quick Start Manual preview
Precis-BX305
Brand: TERSUS Pages: 7
COMBA TB-1800 Equipment Manual preview
TB-1800
Brand: COMBA Pages: 57
Icop VMXP-6453 User Manual preview
VMXP-6453
Brand: Icop Pages: 31
Renfert SILENT C2 Manual preview
SILENT C2
Brand: Renfert Pages: 29
Shenzhen MEITRACK MVT380 User Manual preview
MEITRACK MVT380
Brand: Shenzhen Pages: 8
Honeywell 057810 Manual preview
057810
Brand: Honeywell Pages: 60
StarTech.com ST10GPEXNDPI Quick Start Manual preview
ST10GPEXNDPI
Brand: StarTech.com Pages: 2
Samsung C2316 Manual preview
C2316
Brand: Samsung Pages: 328

Brands by name

Popular brands

Load more brands