manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

II CORE BLOCK: CLG (Clock Generator)

S1C33L03 FUNCTION PART

EPSON

B-II-6-9

A-1

B-II

CLG

Programming Notes

 (1) Immediately after the high-speed (OSC3) oscillation circuit is turned on, a certain period of time is required

for oscillation to stabilize (for a 3.3-V crystal resonator, this time is 10 ms max.). To prevent the device from

operating erratically, do not use the clock until its oscillation has stabilized.

In particular, if the CPU is set in SLEEP mode during operation using the OSC3 clock, the high-speed

(OSC3) oscillation circuit is turned off during in SLEEP mode and starts oscillating again after SLEEP mode

is exited. To prevent the CPU from operating erratically at restart due to an unstable OSC3 clock, set a

sufficient stabilization waiting time in 8-bit programmable timer 1 to turn on the oscillation stabilization

waiting function after SLEEP mode is exited before entering SLEEP mode.

 (2) The oscillation circuit used for the CPU operating clock cannot be turned off.

 (3) The CPU operating clock can only be switched over when both the OSC3 and OSC1 oscillation circuits are

on. Furthermore, when turning off an oscillation circuit that has become unnecessary as a result of the CPU

operating clock switchover, be sure to use separate instructions for switchover and oscillation turnoff. If these

two operations are processed simultaneously using one instruction, the CPU may operate erratically.

 (4) If the high-speed (OSC3) oscillation circuit is turned off, all peripheral circuits operated using the OSC3

clock will be inactive.

 (5) If the OSC3 clock is unnecessary, use the OSC1 clock to operate the CPU and turn the high-speed (OSC3)

oscillation circuit off. This helps reduce current consumption.

 (6) In HALT mode, since the DMA and BCU clocks operate, if the next operation is performed in HALT mode,

not HALT2 mode, with a setting of 0 in clock option register HLT2OP (D3/0x40190), that operation will be

an unpredictable erroneous operation.

If a DMA trigger occurs and DMA is invoked while the CPU is stopped after HALT mode execution,

erroneous operation will result. Ensure that DMA is not invoked in HALT mode.

In HALT2 mode, DMA is not invoked since the DMA and BCU clocks are stopped.

 (7)  In the SLEEP mode, the oscillation circuit clock stops, and in the HALT2 mode, the clocks for peripheral

circuits maintain the status before entering HALT2 (stop or run).

When restarting from this state, interrupt input from a port can be used as a trigger, but functionally, this

interrupt input operates as level input. Therefore, a level input based restart is performed even in the case of

set edge input.

Restart operation is as follows for rising and falling edges.

In case of rising edge interrupt setting:

Restarted by high level input.

In case of falling edge interrupt setting: Restarted by low level input.

In normal operation, a restart begins following the elapse of a given time after execution of the SLP

instruction, but when restart by a falling (rising) level (edge) is set, the operation is as follows.

• The  restart  is effected immediately after execution of the SLP instruction.

• As  ports are already at the low level when the SLP instruction is executed, there is no falling (rising) edge,

and therefore the SLEEP state is entered only momentarily, and the restart is effected immediately

afterwards.

There was a synchronization circuit using a clock signal in the port input circuit, and as the clock is stopped

in the SLEEP state and the clock can be stopped in the HALT2 state, the configuration provided for this

synchronization circuit to be bypassed when restarting. Therefore, a restart is effected when the input level

from a port is active by level. Consequently, the system design should assume that a restart by means of port

input from the SLEEP state or HALT2 state is performed by level.

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

LAWO edge User Manual preview
edge
Brand: LAWO Pages: 154
Octavo OSD3358-SM-RED Getting Started Manual preview
OSD3358-SM-RED
Brand: Octavo Pages: 28
Obihai OBi110 Quick Start Manual preview
OBi110
Brand: Obihai Pages: 2
Hama FireWire Combo Instructions Manual preview
FireWire Combo
Brand: Hama Pages: 8
Zonet ZUN2200 Quick Installation Manual preview
ZUN2200
Brand: Zonet Pages: 2
XMOS XC-2 Quick Start Manual preview
XC-2
Brand: XMOS Pages: 6
JETWAY LI1B Series User Manual preview
LI1B Series
Brand: JETWAY Pages: 55
Dantel 46020-38 Installation & Operation Manual preview
46020-38
Brand: Dantel Pages: 62
UfiSpace S9600-64X Hardware Installation Manual preview
S9600-64X
Brand: UfiSpace Pages: 35
Point of View SmartTV 210 User Manual preview
SmartTV 210
Brand: Point of View Pages: 13
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Brand: impinj Pages: 60
ICOP Technology BF01 User Manual preview
BF01
Brand: ICOP Technology Pages: 34
Gearlinx NR4400 Series User'S Quick Start Manual preview
NR4400 Series
Brand: Gearlinx Pages: 23
Vega ARIES v3.0 Product Reference Manual preview
ARIES v3.0
Brand: Vega Pages: 12
Raven RFMOW V2 User Manual preview
RFMOW V2
Brand: Raven Pages: 33
ATI Technologies Radeon Online Manual preview
Radeon
Brand: ATI Technologies Pages: 87
VIA Technologies Mobile360 M810 Quick Start Manual preview
Mobile360 M810
Brand: VIA Technologies Pages: 25
ZyXEL Communications POE-12 Specifications preview
POE-12
Brand: ZyXEL Communications Pages: 2

Brands by name

Popular brands

Load more brands