manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

VII LCD CONTROLLER BLOCK: LCD CONTROLLER

B-VII-2-22

EPSON

S1C33L03 FUNCTION PART

The following is the power-down procedure.

1. Place the LCD controller in power-save mode (LPSAVE = "0b00").

2. The LCD controller starts a power-down sequence and turns off the power to the LCD panel a one-frame period

later, then pulls LCD signals low.

3. Because the bus clock is turned off during HALT2 or SLEEP mode, the one-frame period described above must

elapse before the chip can be placed in standby mode.

The number of frames can be counted by reading VNDPF (D7)/vertical non-display period register

(0x39FFEA) repeatedly. VNDPF is set to "1" during the vertical non-display period (set to "0" during the

display period).

Depending on the power supply for the LCD panel, it may be necessary to secure more than one frame of power-on

time, otherwise electricity may not be fully discharged within a one-frame period following power-off. In such a

case, exclusive power-up/power-down sequences may be programmed. Control examples are shown below.

Example of a power-up sequence
(for controlling the length of time before the LCD power turns on after LCD signals are asserted)

1. Set LPWREN to "0". The LCDPWR signal is fixed low, with control by a power-up sequence disabled.

2. Release power-save mode (LPSAVE = "0b11").

3. The LCD signals go active a one-frame period after step 2.

4. Allow for a wait time until the power turns on. To set the wait time in terms of the number of frames, count the

occurrences of VNDPF = "1" (vertical non-display period).

5. Set LPWREN to "1" a specified length of time later. The LCDPWR pin goes high, causing the power to the

LCD panel to turn ON.

Example of a power-down sequence
(for controlling the length of time before LCD signals are deasserted after the LCD power turns off)

1. Set LPWREN to "0". The LCDPWR pin goes low, and the power to the LCD panel turns off.

2. Allow for a wait time until LCD signals are deasserted. To set the wait time in terms of the number of frames,

count the occurrences of VNDPF = "1" (vertical non-display period).

3. Set power-save mode a specified length of time later (LPSAVE = "0b00").

4. LCD signals are deasserted a one-frame period after step 3.

Reading/Writing Display Data

The LCD controller contains an exclusive DMA interface, allowing data to be taken in from the display memory by

means of DMA transfer. The display data read from the display memory is buffered in the internal 16 

×

 16-bit

FIFO, preventing the bus efficiency from decreasing. If the data in the FIFO decreases to (0xf - FIFOEO[3:0])

words or less, the LCD controller outputs a DMA request to the CPU requesting that the data be read. Although

any value from 0 to 0xf can be written to FIFOEO[3:0] (D[6:3])/FIFO control register (0x39FFF4), we recommend

setting the value 8.

There are no timing limitations when data is written to the display memory by a user program using the above

DMA transfer. Data can be written asynchronously with the display.

Setting the Display Start Address

The LCD controller is initially set in such a way that data is displayed beginning with the initial address of the

display memory (the area selected by the VRAMAR bit). Because the display memory address from which to start

display can be changed as desired using the screen 1 start address register (0x39FFEC–0x39FFED, D0/0x39FFF0),

it is possible to set a virtual screen for panning or scrolling, as will be described later. The start address set in the

screen 1 start address register corresponds to the upper left edge of the LCD panel.

The value that should actually be set in this register is an offset address from the beginning of the area in which the

display memory exists. When area 7 is used, for example, the start address of the display memory is 0x0, rather

than 0x400000. Be aware that the address set here is a halfword address (byte address for portrait mode; described

later).

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

Lauterbach C2000 Manual preview
C2000
Brand: Lauterbach Pages: 61
Safety Vision ROADRECORDER 8000 User Manual preview
ROADRECORDER 8000
Brand: Safety Vision Pages: 40
ebm-papst 4112 N/2HU Operating Manual preview
4112 N/2HU
Brand: ebm-papst Pages: 6
ebm-papst 4314 N/2HHPU Operating Manual preview
4314 N/2HHPU
Brand: ebm-papst Pages: 6
ebm-papst 8312 L Operating Manual preview
8312 L
Brand: ebm-papst Pages: 5
Delta M125HV-113 Quick Installation Manual preview
M125HV-113
Brand: Delta Pages: 2
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
Dataprobe iBoot-Exp Manual preview
iBoot-Exp
Brand: Dataprobe Pages: 5
KonNad SinoCon C2000-C2-SHK0401-BB1 User Manual preview
SinoCon C2000-C2-SHK0401-BB1
Brand: KonNad Pages: 12
Rane HAL1x System Installation Manual preview
HAL1x
Brand: Rane Pages: 128
Acard AEC-6885 User Manual preview
AEC-6885
Brand: Acard Pages: 34
Shure DFR22 Software Manual preview
DFR22
Brand: Shure Pages: 113
3Com 3C433279A Release Note preview
3C433279A
Brand: 3Com Pages: 12
Arctic Accelero TWIN TURBO II Installation Manual preview
Accelero TWIN TURBO II
Brand: Arctic Pages: 2
Meinberg CPU-C15G2 Setup Manual preview
CPU-C15G2
Brand: Meinberg Pages: 14
B+B SmartWorx Airborne M2M ABDN-er-DP55 Series User Manual preview
Airborne M2M ABDN-er-DP55 Series
Brand: B+B SmartWorx Pages: 120
DigiTech RP 3 User Manual preview
RP 3
Brand: DigiTech Pages: 28
National Instruments USB device 622x User Manual preview
USB device 622x
Brand: National Instruments Pages: 23

Brands by name

Popular brands

Load more brands