manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

II CORE BLOCK: ITC (Interrupt Controller)

B-II-5-4

EPSON

S1C33L03 FUNCTION PART

Trap Table

The C33 Core Block allows the base (starting) address of the trap table to be set by the TTBR register.

TTBR0 (D[9:0]) / TTBR low-order register (0x48134): Trap table base address [9:0] (fixed at "0")

TTBR1 (D[F:A]) / TTBR low-order register (0x48134): Trap table base address [15:10]

TTBR2 (D[B:0]) / TTBR high-order register (0x48136): Trap table base address [27:16]

TTBR3 (D[F:C]) / TTBR high-order register (0x48136): Trap table base address [31:28] (fixed at "0")

After an initial reset, the TTBR register is set to 0x0C00000.

Therefore, even when the trap table position is changed, it is necessary that at least the reset vector be written to the

above address.

TTBR0 and TTBR3 are read-only bits which are fixed at "0". Therefore, the trap table starting address always

begins with a 1KB boundary address.

The TTBR register is normally write-protected to prevent them from being inadvertently rewritten. To remove this

write protection function, another register, TBRP (D[7:0]) / TTBR write-protect register (0x4812D [byte]), is

provided. A write to the TTBR register is enabled by writing "0x59" to TBRP and is disabled back again by a write

to the most significant byte of the TTBR register (0x48137). Consequently, a write to the TTBR register needs to

begin with the low-order half-word first. However, since an occurrence of NMI or the like between writes of the

low-order and high-order half-words would cause a malfunction, it is recommended that the register be written in

words.

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

Lanner NCA-2510 Installation Manual preview
NCA-2510
Brand: Lanner Pages: 2
Dialogic EDP-10 Quick Install Manual preview
EDP-10
Brand: Dialogic Pages: 2
Hanwha Techwin Wisenet PRN-6400B4 Quick Manual preview
Wisenet PRN-6400B4
Brand: Hanwha Techwin Pages: 14
ZALMAN FS-V7 User Manual preview
FS-V7
Brand: ZALMAN Pages: 9
Ubiquiti UniFi WiFi BaseStation XG Quick Start Manual preview
UniFi WiFi BaseStation XG
Brand: Ubiquiti Pages: 19
CG Emotron OSTO 100 Instruction Manual preview
Emotron OSTO 100
Brand: CG Pages: 112
Cypress Semiconductor CY7C1303BV25 Specification Sheet preview
CY7C1303BV25
Brand: Cypress Semiconductor Pages: 19
Crown PIP-AF Owner'S Manual preview
PIP-AF
Brand: Crown Pages: 7
ICP DAS USA PIO-821 Series User Manual preview
PIO-821 Series
Brand: ICP DAS USA Pages: 62
NEC EP-753304DU-R User Manual preview
EP-753304DU-R
Brand: NEC Pages: 26
National Instruments PXI Express PXIe-1085 Series User Manual preview
PXI Express PXIe-1085 Series
Brand: National Instruments Pages: 89
Yeastar Technology YE110 Instruction preview
YE110
Brand: Yeastar Technology Pages: 2
Intel P4000CR Installation Instructions Manual preview
P4000CR
Brand: Intel Pages: 11
Curtiss-Wright KAD/UBM/105 Quick Start Manual preview
KAD/UBM/105
Brand: Curtiss-Wright Pages: 12
Curtiss-Wright GT200 VME Hardware Reference Manual preview
GT200 VME
Brand: Curtiss-Wright Pages: 58
Crestron 2 Channel Inductor Module CLX-2IND Specification Sheet preview
2 Channel Inductor Module CLX-2IND
Brand: Crestron Pages: 1
Extron electronics Scalable Multi-Graphic Videowall Processors MGP 464W Series Specifications preview
Scalable Multi-Graphic Videowall Processors MGP 464W Series
Brand: Extron electronics Pages: 2
Sony Vaio PCWA-C300S Specifications preview
Vaio PCWA-C300S
Brand: Sony Pages: 1

Brands by name

Popular brands

Load more brands